شركة ونزهو برانس للمعدات الهيدروليكية المحدودة
كيف تختيار صمام تجزئة هيدروليكي للمعدات ذات المشغلات المتعددة؟
Sectional valve selection for multi-actuator equipment starts with an actuator-to-section map. Build that map first, then add inlet, flow-sharing and control details so the RFQ describes a real bank instead of a vague valve request.

Part 1. Why does multi-actuator equipment need a section map?
Each work function may need a different spool, flow and holding behavior. A single generic valve description cannot capture simultaneous functions on one machine.
Part 2. Which inlet and flow-sharing questions come next?
State pump flow into the inlet section, whether functions operate together, and whether priority or load-sense logic is required. Simultaneous flow demand often changes bank sizing.
Part 3. How should each section be described for quotation?
| Section field | Example | أرسل مع اقتباس |
|---|---|---|
| Actuator served | Boom / crowd / swing | نعم |
| Spool / center need | Float, hold, motor | نعم |
| Approx. flow | Continuous / peak | نعم |
| Control interface | Lever, solenoid, electrohydraulic | نعم |
Number the sections in machine order so assembly orientation stays clear.

Part 4. Which work-port and relief details are easy to omit?
Port sizes, relief location, anticavitation needs and auxiliary valves at the section often decide whether a bank fits. Capture them before assuming a standard mid-section is enough.
Part 5. How do control interfaces affect the whole bank?
A mixture of manual, solenoid and joystick inputs changes end-section and wiring needs. State the preferred interface per section instead of one label for the entire valve.
Part 6. What package makes a sectional-valve RFQ reviewable?
Provide actuator map, inlet flow, pressure, fluid, section-by-section notes, envelope limits and control interfaces.
- Product-family route: valve range review after the section map is complete
- Send with quote: section table and inlet arrangement
- Fit boundary: bank configuration is assembly-specific

مهم: Do not quote a sectional bank from actuator count alone; section functions, inlet flow and interfaces must be mapped first. — صيغ هيدروليكية أساسية من باركر
استخدم الإرشادات التالية ذات الصلة أثناء المراجعة:
لمراجعة عائلة المنتج، ابدأ بـ نطاق الصمامات الهيدروليكية, راجع مسار الصمام الاتجاهي 4WE عند الاقتضاء، ثم قدم الطلب الكامل من خلال صفحة الاتصال. يتطلب التوصية بالنموذج ورقة البيانات المطبقة ومدخلات التشغيل الكاملة.
الأسئلة الشائعة
What is a hydraulic sectional valve?
A valve assembly built from inlet, work and end sections so multiple actuators can be controlled in one bank.
Why list every actuator in the RFQ?
Each actuator can need a different spool, flow and control interface.
Does inlet flow equal the sum of all section flows?
Not always. Simultaneous versus sequential operation changes the required inlet capacity.
Can sectional and monoblock valves be compared casually?
Only after function count, serviceability and envelope needs are stated.
What control details matter for a bank?
Per-section operator type, electrical data and any joystick or remote requirement.
ما المعلومات التي ينبغي على المشتري تقديمها؟
Actuator map, flows, pressures, fluid, interfaces, envelope and documentation needs.
المراجع
- صيغ هيدروليكية أساسية من باركر — flow and pressure inputs used when mapping multi-actuator sectional banks.
- المعلومات التقنية لسلسلة دانفوس 40 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

