شركة ونزهو برانس للمعدات الهيدروليكية المحدودة
صمام اختيار هيدروليكي: اختر مسار الدائرة الصحيح بدون وظائف صمام الخلط
A hydraulic selector valve switches supply from one inlet arrangement to one of two or more work circuits so a single pump or manifold can serve alternate functions—typically one active path at a time. Upstream directional controls still handle extend, retract, or stop on whichever circuit is connected. The sections below separate selector path selection from priority valves, flow dividers, directional motion control, and flow regulation, then list configuration checks and RFQ inputs worth confirming before a valve conversation.

What a hydraulic selector valve is (and is not)
A hydraulic selector valve switches supply from one inlet arrangement to one of two or more work circuits. In plain language, it picks which downstream function receives oil from the shared source.
Buyers also see the same circuit-switching job marketed as a صمام تحويل هيدروليكي. For diverter-first mobile framing, see the صمام تحويل هيدروليكي guide. This article keeps selector as the primary keyword for industrial multi-circuit path selection.
Selectors belong to the directional-control valve family because an internal spool, ball, or poppet element shifts to connect different port paths. A selector answers which circuit is live, not how fast an actuator moves.
كما أنه ليس flow regulator or a generic صمامات التحكم الهيدروليكية overview. A check valve / relief valve pair solves holding reverse flow and limiting pressure—different jobs from path selection.
How selector valves switch circuit paths
In a shared-control pattern, the selector connects one set of work ports / circuits at a time while the unused path stays blocked. Once a path is live, the directional valve on that branch still governs extend, retract, and stop for the connected actuator.
The selector uses that family mechanism for circuit choice before motion commands reach the active branch.
Manual / solenoid / pilot actuation can shift the path. Treat actuation as a configuration question confirmed against model documentation, not as a field install recipe.

Selector vs diverter naming vs directional control
Selector and diverter are often interchangeable labels for the same circuit-switching job, with regional naming differences. The hardware still picks one active work path at a time.
A selector chooses which downstream circuit receives flow. Directional hardware on the active branch still governs extend, retract, and stop for the connected actuator.
Prance’s الصمام الاتجاهي 4WE route documents motion control on the connected circuit. It is adjacent to selector logic, not a named selector SKU.
A true third function / dedicated section adds its own control path when simultaneous use is part of the machine plan.
| وظيفة المشتري | ما يفعله العتاد بشكل رئيسي | نتيجة بلغة بسيطة |
|---|---|---|
| Selector / diverter path switching | Routes all supply to one chosen work path | One shared source serves alternate functions, usually one at a time |
| بدء/إيقاف/اتجاه اتجاهي | Controls extend, retract, or stop on the connected circuit | Motion control after the path is selected |
| قسم مخصص إضافي / وظيفة ثالثة حقيقية | يضيف مسار تحكم مخصص بدلاً من مشاركة صمام واحد | الهندسة المختارة عندما يكون الاستخدام المتزامن جزءًا من الخطة |
Selector vs priority valve vs flow divider
Buyers often confuse path selection with path splittingcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
A cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
A مقسم التدفق cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ما يفعله العتاد بشكل رئيسي | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
|---|---|---|
| Selector path switching | Routes all supply to one chosen path | Primary topic |
| Priority valve | Primary flow first, excess to secondary | Use when bypass sharing is required |
| Flow divider | Splits inlet into proportional outputs | Use when both branches need simultaneous shares |

عدد المنافذ، حالة المركز، وفحوصات التفعيل
Selection service is commonly described as one inlet changing over between two outlets. A 3 way selector valve label—and broader 3-way / 6-way port arrangement notes—describe path geometry, not performance ratings.
Center-type labels—open center / closed center—describe what happens between full work-path positions. Confirm the center condition against model documentation for the circuit you are matching.
Record port arrangement, center condition, and actuation beside flow, pressure, mounting, and fluid cleanliness before supplier discussions.

Simultaneous use and multi-circuit trade-offs
Shared-control selectors often cannot run the original and diverted functions at the same time. That sequential limit is the main trade-off buyers weigh against a true third function / dedicated section.
من الميدان: Equipment-forum buyers often accept sequential function access as the trade-off for shared-source path switching—one active hydraulic function at a time unless a dedicated third-function path exists. See the TractorByNet thread on diverter vs. true third function for representative community language.
Stacking multiple path switches can expand how many functions share a source, yet hose layout and work-port accessibility still need confirmation in the circuit plan.
بناء صورة الاختيار قبل مناقشة الصمام
Start with circuit function, rated flow, working pressure, command method, mounting interface, port geometry, fluid type, and cleanliness class—the same starter fields the valves hub publishes for RFQ discussions.
Document whether the machine needs alternate paths only, or simultaneous branches with priority or divider hardware. That single architecture note prevents a selector conversation from starting when the real need is flow sharing.
Use the checklist to confirm whether the enquiry is path selection, motion control on one path, or speed metering. Undefined simultaneous-use needs or missing electrical-interface data are reasons to pause before naming a valve type.
| المعلومات التي يجب جمعها | لماذا تنتمي إلى المحادثة | توضيح المثال |
|---|---|---|
| وظيفة الدائرة | Separates selector path switching from directional motion or flow metering | Is the request circuit selection, speed control, or motion on one path? |
| Rated flow and pressure | Ties the valve talk to active-circuit demand | What flow and pressure does the selected path require? |
| Command method / electrical interface | Matches manual, solenoid, or pilot actuation | Which operator input and coil interface apply? |
| Mounting interface and ports | Defines the mechanical connection | Which mounting pattern and port sizes are in the circuit? |
| Fluid type and cleanliness class | Describes the operating environment | Which fluid and filtration class apply? |
سياق المنتج: محور صمامات هيدروليكية ومسارات 4WE / 4WRAE المجاورة
ينشر برانس مسار عائلة منتجات الصمامات الهيدروليكية التي تغطي الخيارات الاتجاهية والنسبية. ال محور الصمامات الهيدروليكية with the checklist above before naming a product family.
ال الصمام الاتجاهي 4WE cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits صمام التناسب 4WRAE cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
الأسئلة الشائعة
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
For circuit-switching jobs, selector and diverter are commonly treated as interchangeable market labels, with regional naming differences. See the hydraulic diverter valve article for diverter-first mobile framing.
How is a selector different from a directional control valve?
A selector chooses which downstream circuit receives supply. Directional control starts, stops, and reverses motion on the circuit already connected to the active path.
How is a selector different from a priority valve or flow divider?
A selector routes all supply to one chosen path. A priority valve feeds a primary branch first and sends excess to a secondary path; a flow divider shares inlet flow between proportional branches.
Can I operate both functions at once with a selector?
Shared-control selector setups usually cannot run both functions simultaneously. Confirm the architecture: if simultaneous use is required, a priority valve, flow divider, or dedicated extra section may be the better starting point.
What do 3-way and 6-way selector labels mean?
إنها تسميات عدد المنافذ والهندسة المكانية للمسار لشرح كيفية تبديل جسم الصمام للدارات. إنها مفردات التكوين، وليست تصنيفات التدفق أو الضغط.
ما المعلومات التي يجب أن أجهزها قبل السؤال عن خيارات الصمامات؟
Start with circuit function, rated flow, working pressure, command method, mounting interface, ports, fluid type, and cleanliness class—the fields the valves hub lists for RFQ discussions.
Is a selector a check valve or a relief valve?
No. A selector switches circuits; a check valve holds reverse flow and a relief valve limits pressure. Keep those protection jobs on their own articles when the buying question is holding or overpressure protection.

