A6VE Variable Displacement Plug-In Motor

The A6VE is a variable displacement plug-in motor, not a fixed displacement motor. Its bent-axis rotary group changes displacement, while the recessed mounting arrangement must match the receiving gearbox and shaft.

  • Variable displacement bent-axis motor
  • Plug-in mounting arrangement
  • Flushing and boost valve options
  • Counterbalance option depends on order code

PRANCE HYDRAULIC · PRODUCT SERIES

A6VE Variable Displacement Plug-In Motor

Axial piston; bent axis, variable displacement · Confirm open or closed circuit configuration

The A6VE is a variable displacement plug-in motor, not a fixed displacement motor. Its bent-axis rotary group changes displacement, while the recessed mounting arrangement must match the receiving gearbox and shaft.

Model

✓A6VE original product photograph
A6VEAxial piston; bent axis, variable displacement
Request a QuotationVer Datos Técnicos y Ficha Técnica

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Configuration review · Technical documentation · Product selection

Detalles del producto

  • Variable displacement bent-axis motor
  • Plug-in mounting arrangement
  • Flushing and boost valve options
  • Counterbalance option depends on order code

CATEGORIES: Motor de pistón, Motor de pistones de cilindrada variable

A6VE Features & Application

Variable displacement bent-axis motor

Specify the displacement range or switching arrangement and verify performance at each required setting.

Plug-in mounting arrangement

Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.

Flushing and boost valve options

Account for pilot or replenishment demand and the relevant pressure limits. Include filtration and the return or drain route in the circuit review.

Counterbalance option depends on order code

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

A6VE Specifications

Series / modelA6VE
Product typeA6VE Variable Displacement Plug-In Motor
DiseñoAxial piston; bent axis, variable displacement
Circuit / selectionConfirm open or closed circuit configuration
Published technical-table sizes28 and 250
Listed maximum displacement28.1 and 250 cm³/rev respectively
Displacement settingConfirm the ordered minimum, maximum and control

A6VE Selection & Configuration

The A6VE is a variable displacement plug-in motor, not a fixed displacement motor. Its bent-axis rotary group changes displacement, while the recessed mounting arrangement must match the receiving gearbox and shaft.

Supply the gearbox interface drawing and the full control code. Check maximum speed at each displacement setting, case filling and the drain route. A zero-displacement capability in a family description is not a holding function and does not establish the permitted setting for every application.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

A6VE Buying Guide

Use this sequence to prepare the A6VE configuration for review and quotation.

  1. Define starting and continuous torque, speed range and duty cycle.
  2. Specify available flow, work-port pressure difference and return pressure.
  3. Confirm the displacement setting and required behavior during starting and stopping.
  4. Check shaft, mounting pilot, flange, port orientation and external loads.
  5. Review case drainage, replenishment and any displacement control.
  6. Specify fluid conditions and any independent braking requirement.
  7. Approve the complete model, operating envelope, drawing and quantity.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Project Inquiries

Learn more →

Send your required model, quantity, application and project requirements to discuss your inquiry.


Product inquiries · Configuration review

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your A6VE Application

Send the full model code, operating duty, installation details and quantity.

Request a A6VE Quotation

A6VE Questions Before Ordering

What type of product is the A6VE?

A6VE Variable Displacement Plug-In Motor. Design: Axial piston; bent axis, variable displacement. Confirm open or closed circuit configuration. Confirm the complete order code for the offered version.

Can a similar motor replace the A6VE?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

A6VE Technical Data & Documents

View A6VE catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Datos técnicos

Tamaño NG 28 250
Desplazamiento geométrico, por revolución1) Vgmax cm3 28.1 250
Vgmin cm3 0 0
Vgracias cm3 18 205
Velocidad máxima de giro2) (in compliance with maximum permissible inlet flow) a las VG máximo nNombre rpm 5550 2700
a las Vg < Vgracias (ver diagrama) nmáx rpm 8750 3300
a las Vg 0 nmáx rpm 10450 3300
Caudal de entrada en yNombre y VG máximo qv máx l/min 156 675
Par de torsión3) a las VG máximo y ΔP ▪ 400 bar M Nm 179 –
a las VG máximo y ΔP ▪ 350 bar M Nm 157 1391
Rigidez torsional VG máximo a Vg/2 Cmín kNm/rad 6 60
Vg/2 a 0 (interpolado) Cmín kNm/rad 18 181
Momento de inercia del grupo rotatorio JTw kgm2 0.0014 0,061
Volumen de casos V l 0.5 3.0
Peso aprox. con placa de orificio 02, 38 m kg 16 1105)

▼Desplazamiento admisible en función de la velocidad de giro

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Determinación de las características

Determinación de las características
Caudal de entrada qv=(Vg×n)/(1000×ηv) l/min
Velocidad de giro n=(qv×1000×ŋv)/Vg rpm
Par de torsión M=(Vg×Δp×ŋhm)/(20×π) Nm
Poder P=(2π×M×n)/60000=(qv×Δp×ŋt)/600 kW

Clave

Vg Desplazamiento por revolución [cm3]
Δp Presión diferencial [bar]
n Velocidad de giro [rpm]
ŋv Eficiencia volumétrica
ŋhm Rendimiento hidráulico-mecánico
ŋt Eficiencia total (t = 7v x 7hm)

Aviso

▶Theoretical values, without efficiency and tolerances;values rounded ▶Operation above the maximum values or below the minimum values may result in a loss of function,a reduced service life or in the destruction of the axial piston unit. Other permissible limit values, such as speed variation, reduced angular acceleration as a function of the frequency and the permissible angular acceleration at start (lower than the maximum angular acceleration) can be found in data sheet 90261. 1) The minimum and maximum displacement can be steplessly varied,see Ordering code on page 2. (Standard setting size 250 if not Specified when ordering: Vgmin = 0,2×Vg máx, Vg máx = Vg máx). 2) The values are applicable: – for the optimum viscosity range from νelegir = 36 a 16 mm2/s – with hydraulic fluid based on mineral oils 3)Torque without radial force, with radial force see page 8 4)Values in this range on request 5)Port plate 02

Carga radial y axial admisible en los ejes de transmisión

Tamaño NG 28 250
Árbol de transmisión W30 W50
Fuerza radial máxima1) a la distancia a (del anillo de fijación) cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Fcuántos máximos N 4838 12002)
a mm 17.5 41
Par máximo en Fcuántos máximos Tcuántos máximos Nm 179 3)
Presión diferencial máxima en Vgmax y Fqmax Δpcuántos máximos bar 400 3)
Fuerza axial máxima, con la máquina detenida o en funcionamiento sin presión cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits + Fax max N 0 0
– Fax max N 315 1200
Fuerza axial permisible por barra de presión de trabajo + Fpérdida/barra ax N/bar 4.6 3)

Efecto de la fuerza radial Fq sobre la vida útil de los rodamientos

Al seleccionar una dirección adecuada de la fuerza radial Fq, the load on the bearings, caused by the internal rotary group forces can be reduced, thus optimizing the bearing service life.Recommended position of mating gear is dependent on the direction of rotation. Examples: ▼Gear output drive cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits 1 “Counter-clockwise” rotational direction, pressure at port B 2 “Clockwise” rotational direction, pressure at port A 3 Bidirectional direction of rotation

Aviso

▶The values given are maximum values and do not apply to continuous operation. ▶The permissible axial force in direction -Fax is to be avoided as the bearing service life is reduced. ▶Special requirements apply in the case of belt output drives. Please contact us. 1)With intermittent operation 2)When at standstill or when axial piston unit working in depressurized conditions. Higher forces are permissible under pressure, please contact us. 3) Please contact us.

Request a A6VE Quotation

Tell us your required configuration, quantity and application.

Demostración de formulario de contacto
A6VE original product photograph

Escribe código

Unidad de pistones axiales

01 Diseño de eje inclinado, variable A6V

Modo de operación

02 Motor enchufable E

Tamaño (NG)

03 Desplazamiento geométrico, véase "Datos técnicos" 28 250

Dispositivo de control

28 250
04 Control proporcional, hidráulico ΔPest=10 bar ● ● HD1
ΔPest=25 bar ● ● HD2
Control proporcional, eléctrico U=12V ● ● EP1
U=24V ● ● EP2
Control de dos puntos
hidráulico
- ● Hz
● - HZ1
Control de dos puntos
eléctrico
U=12V ● ● EZ1
U=24V ● ● EZ2
Control automático
dependiente de alta presión
con un aumento mínimo de presión ΔP ≤ aprox. 10 bar ● ● HA1
con el aumento de la presión ΔP=100 bar ● ● HA2
Control automático, relacionado con la velocidad Pest/PHD = 3/100, válvula direccional de recorrido hidráulico - ● DA
Pest/PHD = 5/100, válvula de dirección de desplazamiento eléctrico + conmutación eléctrica Vgmax U=12V ● - DA3

Control de presión (solo para HD y EP)

28 y 250
05 Sin control/anulación de presión ● ●
Control de presión, ajuste fijo ● ● D

Control/anulación de presión

28 y 250
06 Sin control/anulación de presión ● ●
Anulación de los mandos HA1 y HA2, teledirigidos hidráulicamente, proporcionales ● ● T

Series

07 Serie 6, índice 3 63

Sentido de giro

08 Visto en el eje de transmisión, bidireccional W

Establecer rango para el desplazamiento1)

28 250
09 Vg min =0 a 0,7 VG máximo(sin código) ● -
Vg min =0 a 0,4 VG máximo                                           VG máximo = VG máximo a 0,8 VG máximo - ● 1
Vg min > 0,4 VG máximo a 0,8 VG máximo                                VG máximo = VG máximo a 0,8 VG máximo - ● 2

Material de sellado

28 250
10 retén de eje de FKM (fluoroelastómero) ● ● V

Árbol de transmisión

28 250
11 Eje ranurado DIN 5480 ● - A
- ● Z

•=Disponible       ○=Bajo petición          -=No disponible           =Programa preferido

1) Por favor, especifique la configuración exacta para Vgmin y Vgmax en texto plano al ordenar: Vgmin = ... cm3, Vgmax = ... cm3

Brida de montaje

28 250
12 Similar a la norma ISO 3019-2 de 2 agujeros ● - L
de 4 agujeros - ● M

Puerto de trabajo2)

28 250
13 puertos de trabajo SAE A y B al lado, enfrente 02 0 ● ● 020
7 ● ● 027
Placa de conexión para montaje de válvula de contrapeso, con válvula limitadora de presión de 1 etapa (de acción pilotada)3) 38 0 - ●4) 380

Válvulas

14 Sin 0
Válvula de purga y de presión de sobrealimentación, montada 7
Válvula de contrapeso montada 8

Sensor de velocidad

28 250
15 Sin sensor de velocidad ● ● 0
Preparado para sensor de velocidad DSA ○ ● U
sensor de velocidad DSA instalado5) ○ ● V

Conector para solenoides6)

28 250
16 Sin conector (sin solenoide, solo para control hidráulico)
(Tamaño 250 sin código)
● - 0
- ●
conector moldeado DEUTSCH, de 2 pines, sin diodo supresor ● - P
Conector HIRSCHMANN - sin diodo supresor (sin código) - ●

Inicio del control

28 250
17 Placa de puerto 02, 38 a las Vgmin (estándar para HA) ● ● A
a las Vgmax(estándar para HD, HZ, EP, EZ, DA) ● ● B

Versión estándar / especial

18 Versión estándar (sin símbolo)
Versión estándar con variantes de instalación, p. ej., puertos T abiertos o cerrados, al contrario de lo estándar -Y
Versión especial -S

•=Disponible       ○=Bajo petición          -=No disponible           =Programa preferido

Aviso

¡Presta atención a las notas de planificación del proyecto en la página 34!

▶Además del código de tipo, especifique los datos técnicos pertinentes al realizar su pedido.

Tenga en cuenta que no todas las combinaciones de códigos de tipo están disponibles, aunque las funciones individuales aparezcan como disponibles.

2) Rosca de fijación, métrica.

3) Solo posible en combinación con control HD, EP y HA

4) Válvula de contrapeso MHB32, por favor, póngase en contacto con nosotros.

5) Especifique el código de tipo por separado para el sensor de acuerdo con la hoja de datos 95133 (DSA) y observe los requisitos de la electrónica.

6) Los conectores para otros componentes eléctricos pueden diferir.

Datos técnicos

Tamaño NG 28 250
Desplazamiento geométrico, por revolución1) Vgmax cm3 28.1 250
Vgmin cm3 0 0
Vgracias cm3 18 205
Velocidad máxima de giro2)
(en cumplimiento con el máximo
caudal de entrada admisible
a las VG máximo nNombre rpm 5550 2700
a las Vg < Vgracias (ver diagrama) nmáx rpm 8750 3300
a las Vg 0 nmáx rpm 10450 3300
Caudal de entrada en yNombre y VG máximo qv máx l/min 156 675
Par de torsión3) a las VG máximo y ΔP ▪ 400 bar M Nm 179 –
a las VG máximo y ΔP ▪ 350 bar M Nm 157 1391
Rigidez torsional VG máximo a Vg/2 Cmín kNm/rad 6 60
Vg/2 a 0 (interpolado) Cmín kNm/rad 18 181
Momento de inercia del grupo rotatorio JTw kgm2 0.0014 0,061
Volumen de casos V l 0.5 3.0
Peso aprox. con placa de orificio 02, 38 m kg 16 1105)

▼Desplazamiento admisible en función de la velocidad de giro

Determinación de las características

Determinación de las características
Caudal de entrada qv=(Vg×n)/(1000×ηv) l/min
Velocidad de giro n=(qv×1000×ŋv)/Vg rpm
Par de torsión M=(Vg×Δp×ŋhm)/(20×π) Nm
Poder P=(2π×M×n)/60000=(qv×Δp×ŋt)/600 kW

Clave

Vg Desplazamiento por revolución [cm3]
Δp Presión diferencial [bar]
n Velocidad de giro [rpm]
ŋv Eficiencia volumétrica
ŋhm Rendimiento hidráulico-mecánico
ŋt Eficiencia total (t = 7v x 7hm)

Aviso

▶Valores teóricos, sin eficiencia ni tolerancias; valores redondeados

▶El funcionamiento por encima de los valores máximos o por debajo de los valores mínimos puede provocar una pérdida de función, una vida útil reducida o la destrucción de la unidad de pistones axiales. En la hoja de datos 90261 se pueden encontrar otros valores límite permitidos, como la variación de velocidad, la aceleración angular reducida en función de la frecuencia y la aceleración angular permitida en el arranque (inferior a la aceleración angular máxima).

1) El desplazamiento mínimo y máximo se puede variar de forma continua, consulte el código de pedido en la página 2. (Configuración estándar tamaño 250 si no se especifica al realizar el pedido: Vgmin = 0,2×Vg máx, Vg máx = Vg máx).

2) Los valores son aplicables:

- para el rango de viscosidad óptimo de νelegir = 36 a 16 mm2/s

- con fluido hidráulico a base de aceites minerales

3) Par sin fuerza radial, con fuerza radial ver página 8

4) Valores en este rango bajo petición

Placa de orificio 02

Carga radial y axial admisible en los ejes de transmisión

Tamaño NG 28 250
Árbol de transmisión W30 W50
Fuerza radial máxima1) a la distancia a (del anillo de fijación) Fcuántos máximos N 4838 12002)
a mm 17.5 41
Par máximo en Fcuántos máximos Tcuántos máximos Nm 179 3)
Presión diferencial máxima en Vgmax y Fqmax Δpcuántos máximos bar 400 3)
Fuerza axial máxima, con la máquina detenida o en funcionamiento sin presión + Fax max N 0 0
- Fax max N 315 1200
Fuerza axial permisible por barra de presión de trabajo + Fpérdida/barra ax N/bar 4.6 3)

Efecto de la fuerza radial Fq sobre la vida útil de los rodamientos

Al seleccionar una dirección adecuada de la fuerza radial Fq, la carga sobre los cojinetes, causada por las fuerzas internas del grupo rotativo, se puede reducir, optimizando así la vida útil de los cojinetes. La posición recomendada del engranaje acoplado depende del sentido de giro. Ejemplos:

▼ Salida del engranaje

Sentido de giro "antihorario", presión en el puerto B

Dirección de rotación "en sentido horario", presión en el puerto A

3 Sentido de giro bidireccional

Aviso

▶ Los valores indicados son valores máximos y no se aplicarán

a la operación continua.

Se debe evitar la fuerza axial admisible en la dirección -Fax, ya que se reduce la vida útil del rodamiento.

▶Se aplican requisitos especiales en el caso de transmisiones por correa. Póngase en contacto con nosotros.

1) Con funcionamiento intermitente

2) Cuando se encuentre parado o cuando la unidad de pistones axiales trabaje en condiciones despresurizadas. Se permiten fuerzas mayores bajo presión, por favor contáctenos.

3) Por favor, póngase en contacto con nosotros.