Wenzhou Prance Hydraulic Equipment Co., Ltd
A10VZO Variable Speed Axial Piston Pump
The A10VZO variable pump is listed for start/stop, pressure-holding and multiple-quadrant operation. Its selection should therefore include how the drive behaves during decompression and energy return, not just the maximum delivered flow.
- Start/stop operation described
- Pressure-holding duty described
- First, second and fourth quadrant use
- Through-drive option subject to configuration
PRANCE HYDRAULIC · PRODUCT SERIES
Axial piston; variable displacement · Confirm the required quadrant and hydraulic circuit
The A10VZO variable pump is listed for start/stop, pressure-holding and multiple-quadrant operation. Its selection should therefore include how the drive behaves during decompression and energy return, not just the maximum delivered flow.
Modèle

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Étude de configuration · Documentation technique · Sélection de produits
Détails du produit
- Start/stop operation described
- Pressure-holding duty described
- First, second and fourth quadrant use
- Through-drive option subject to configuration
CATÉGORIES : Pompe à piston, Pompe à cylindrée variable
A10VZO Features & Application
Start/stop operation described
Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.
Pressure-holding duty described
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
First, second and fourth quadrant use
Compare the required flow at the actual drive speed and pressure. Check the selected variant rather than combining maxima from different rows.
Through-drive option subject to configuration
Review combined drive torque and simultaneous demand, including any additional pump connected to the drive.
A10VZO Specifications
| Series / model | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
|---|---|
| Product type | A10VZO Variable Speed Axial Piston Pump |
| Conception | Axial piston; variable displacement |
| Circuit / selection | Confirm the required quadrant and hydraulic circuit |
| Published nominal sizes | 3, 6, 8, 10, 18, 28 and 45 |
| Listed maximum geometric displacement | 3.5, 6, 8, 10.5, 18, 28 and 45 cm³/rev |
A10VZO Selection & Configuration
The A10VZO variable pump is listed for start/stop, pressure-holding and multiple-quadrant operation. Its selection should therefore include how the drive behaves during decompression and energy return, not just the maximum delivered flow.
Define the operating quadrants with the drive supplier and identify when hydraulic energy can return to the electric drive. Check lubrication, inlet pressure, control settings and the permitted speed-pressure envelope in each operating state.

Your Application.
The Right Configuration.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

A10VZO Buying Guide
Use this sequence to prepare the A10VZO configuration for review and quotation.
- Define required flow at the actual drive speed and continuous pressure.
- Identify peak pressure, duration and the work cycle.
- Confirm the selected displacement control and any auxiliary-drive requirement.
- Match rotation viewed from the shaft end, shaft, flange and ports.
- Review inlet conditions, drain routing and the installation envelope.
- Confirm fluid, viscosity, temperature, filtration and seals.
- Approve the complete model, control, drawing, quantity and delivery terms.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Learn more →cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your A10VZO Application
Send the full model code, operating duty, installation details and quantity.
Request a A10VZO QuotationA10VZO Questions Before Ordering
What type of product is the A10VZO?
A10VZO Variable Speed Axial Piston Pump. Design: Axial piston; variable displacement. Confirm the required quadrant and hydraulic circuit. Confirm the complete order code for the offered version.
Can a similar pump replace the A10VZO?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.
A10VZO Technical Data & Documents
View A10VZO catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Technical data A10VZO size 3 to 45
| Taille | NG | 3 | 6 | 8 | 10 | 18 | 28 | 45 | ||
| Displacement, geometric,per revolution | Vg max | cm3 | 3.5 | 6 | 8 | 10.5 | 18 | 28 | 45 | |
| Rotational speed maximum1) | à VGiga | |||||||||
| Suction speed operation as a pump1) | nnom | tours par minute | 3600 | 3600 | 3600 | 3600 | 3300 | 3000 | 3000 | |
| Max. speed decompression operation2) | nnom | tours par minute | 3600 | 3600 | 3600 | 3600 | 3300 | 3000 | 3000 | |
| Power Operation as a pump at nnom,Vg max | et Δp = 250 bar | P | kW | 5 | 10 | 15 | 16 | – | – | – |
| and Δp = 315 bar | P | kW | – | – | – | – | 34 | 39 | 44 | |
| Couple | à VGiga et Δp = 250 bar | T | Rien | 14 | 24 | 32 | 42 | – | – | – |
| à VGiga and Δp = 315 bar | T | Rien | – | – | – | – | 90 | 140 | 225 | |
| à VGiga et Δp = 100 bar | T | Rien | 6 | 9 | 13 | 17 | 29 | 140 | 225 | |
| Rotary stiffness of drive shaft | S | c | Nm/rad | 8100 | 8100 | 8100 | 8100 | – | – | – |
| R | c | Nm/rad | – | – | – | – | 14800 | 26300 | 41000 | |
| Moment d'inertie pour le groupe rotatif | JTW | Kgm2 | 0.0006 | 0.0006 | 0.0006 | 0.0006 | 0.00093 | 0.0017 | 0.0033 | |
| Accélération angulaire maximale2)3) | α | rad/s2 | 14000 | 14000 | 14000 | 14000 | 12600 | 11200 | 9500 | |
| Volume du boîtier | V | L | 0.2 | 0.2 | 0.2 | 0.2 | 0.25 | 0.3 | 1.0 | |
| Weight without through drive (14N00, 12N00 approx.) | m | kg | 8 | 8 | 8 | 8 | 12 | 15 | 27 | |
| Weight without through drive (22U00 approx.) | m | kg | – | – | – | – | – | – | – | |
| Weight with through drive (07K.., 12K..approx.) | m | kg | 10.5 | 10.5 | 10.5 | 10.5 | 14 | 18 | 28 | |
| Weight with through drive (22U..approx.) | m | kg | – | – | – | – | – | – | – | |
Définir les caractéristiques de fonctionnement
Clé
Vg Déplacement par révolution en [cm3] Δp Differential pressure [bar] n Rotational speed [rpm] ηv Volumetric efficiency ηhm Hydraulic-mechanical efficiency ηt Efficacité totale (ηt= ηv*ηhm) 1)The values are applicable: – At absolute pressure Pabdos = 1 bar at suction port S – For the optimal viscosity range of vopt = 36 à 16 mm2/s – For hydraulic fluid based on mineral oils 2)Higher values on request 3) The limit value is only valid for a single pump, multiple pump version available on request. The load capacity of the connecting parts must be considered.Technical data A10VZO size 71 to 180
| Taille | NG | 71 | 100 | 140 | 180 | ||
| Displacement, geometric,per revolution | Vg max | cm3 | 71.1 | 100 | 140 | 180 | |
| Rotational speed maximum1) | à VGiga | ||||||
| Suction speed operation as a pump1) | nnom | tours par minute | 2550 | 2300 | 2200 | 1800 | |
| Max. speed decompression operation2) | nnom | tours par minute | On request | ||||
| Couple | à VGiga and Δp = 280 bar | T | Rien | 317 | 445 | 623 | 801 |
| à VGiga et Δp = 100 bar | T | Rien | 113 | 159 | 223 | 286 | |
| Rotary stiffness of drive shaft | S | c | Nm/rad | 8100 | 8100 | 8100 | 8100 |
| R | c | Nm/rad | – | 121142 | 169537 | 171107 | |
| Moment d'inertie pour le groupe rotatif | JTW | Kgm2 | 0.0087 | 0.0185 | 0.0276 | 0.033 | |
| Accélération angulaire maximale2)3) | α | rad/s2 | 7500 | 6200 | 5000 | 4000 | |
| Volume du boîtier | V | L | 1.6 | 2.2 | 3.0 | 2.7 | |
| Weight without through drive (12N00, 42N00 approx.) | m | kg | 36.5 | 55 | 70 | – | |
| Weight without through drive (22U00 approx.) | m | kg | 47 | 69 | 73 | 78 | |
| Weight with through drive (12K..approx.) | m | kg | – | – | – | – | |
| Weight with through drive (22U..approx.) | m | kg | 47 | 69 | 73 | 78 | |
Définir les caractéristiques de fonctionnement
Clé
Vg Déplacement par révolution en [cm3] Δp Differential pressure [bar] n Rotational speed [rpm] ηv Volumetric efficiency ηhm Hydraulic-mechanical efficiency ηt Efficacité totale (ηt= ηv*ηhm) 1)The values are applicable: – At absolute pressure Pabdos = 1 bar at suction port S – For the optimal viscosity range of vopt = 36 à 16 mm2/s – For hydraulic fluid based on mineral oils 2)Higher values on request 3) The limit value is only valid for a single pump, multiple pump version available on request. The load capacity of the connecting parts must be considered. 4) With port plates 7 or 14couples d'entrée et de transmission admissibles
| Taille | 003 to 10 | 18 | 28 | 45 | 71 | 100 | 140 | 180 | |||
| Couple d'entrée | |||||||||||
| at drive shaft, maximum2) | S | TE max | Rien | 126 | – | – | – | – | 1104 | 1620 | 1620 |
| ∅ | in | 3/4 | – | – | – | – | 1 1/2 | 1 3/4 | 1 3/4 | ||
| R | TE max | Rien | – | 160 | 250 | 400 | 650 | – | – | – | |
| ∅ | in | – | 3/4 | 7/8 | 1 | 1 1/4 | – | – | – | ||
| Maximum through- drive torque | S | TD max | Rien | 41 | – | – | – | – | 778 | 1266 | 1266 |
| R | TD max | Rien | – | 92 | 127 | 229 | 480 | – | – | – | |
Répartition des couples
| Couple d'entrée | TE=T1+T2+T3 |
| TE < TE max | |
| Through-drive torque | TD=T2+T3 |
| TD < TD max |
Watch A10VZO Product Video
Related Selection Resources
Request a A10VZO Quotation
Tell us your required configuration, quantity and application.
Type code A10VZ0
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | ||
| A10V | Z | ○ | / | 10 | - | V | C | N00 |
Unité à pistons axiaux
| 01 | Swashplate design, variable | A10V |
Application area
| 02 | Variable-speed drives | Z |
Mode de fonctionnement
| 03 | Pompe à circuit ouvert | ○ |
Taille (NG)
| 04 | Déplacement géométrique, voir le tableau des valeurs à la page 10 | 010 | 018 | 028 | 045 | 071 | 100 | 140 | 180 |
| Other available intermediate sizes | 003,006,008 |
Dispositif de commande
| 05 | Contrôle à deux points | électrique | U=12V | ● | ● | ● | ● | ○ | ○ | ○ | ○ | EZ3001) |
| U=24V | ● | ● | ● | ● | ○ | ○ | ○ | ○ | EZ4001) | |||
| hydraulique | ● | ● | ● | ● | ○ | ○ | ○ | ○ | DGO001) | |||
| Régulateur de pression | hydraulique | ● | ● | ● | ● | ○ | ○ | ○ | ○ | DRO00 | ||
| remote controlled hydraulically | ● | ● | ● | ● | ○ | ○ | ○ | ○ | DRGO0 | |||
| Torque controller | Size 018 to 180 | |||||||||||
| Début du contrôle |
up to 50 bar |
- | ● | ● | ● | ○ | ○ | ○ | ○ | LA5D0 | ||
|
de 51 à 90 bars |
- | ● | ● | ● | ○ | ○ | ○ | ○ | LA6D0 | |||
|
de 91 à 160 bars |
- | ● | ● | ● | ○ | ○ | ○ | ○ | LA7D0 | |||
|
de 161 à 240 bars |
- | ● | ● | ● | ○ | ○ | ○ | ○ | LA8D0 | |||
|
over 240 bar |
- | ● | ● | ● | ○ | ○ | ○ | ○ | LA9D0 | |||
Séries
| 06 | Series 1, index 0 | ● |
Sens de rotation2)
| 07 | Vu sur l'arbre de transmission | dans le sens des aiguilles d'une montre | R |
| dans le sens inverse des aiguilles d'une montre | L |
Matériau d'étanchéité
| 08 | FKM (fluoroélastomère) | V |
Arbre de transmission
| 09 | Arbre cannelé
ANSI B92.1a |
arbre standard | ● | - | - | - | - | ○ | ○ | ○ | S |
| similaire à l'arbre " S ", mais pour un couple d'entrée plus élevé | - | ● | ● | ● | ○ | - | - | - | R |
Bride de fixation
| 10 | ISO 3019-1 (SAE) | à deux trous | ● | ● | ● | - | - | - | - | - | C |
| à 4 trous | - | - | - | ● | ○ | ○ | ○ | ○ | D |
1) Please specify mechanical flow control VGiga et Vsol mineur in the order text.
2)Changing direction of rotation permissible with the same pressure side for decompression
Port en eau profonde3)
| 003 to 010 | 018 | 028 | 045 | 071 | 100 | 140 | 180 | |||
| 11 | SAE flange ports at top and bottom, on opposite sides, metric fastening thread with universal through drive | - | - | - | - | ○ | ○ | ○ | ○ | 22U5) |
| SAE flange ports at top and bottom, on opposite sides, metric fastening thread | - | ● | ● | ● | ○ | ○ | ○ | - | 123)5) | |
| DIN 3852 threaded ports at rear, not for through drive | ● | - | - | - | - | - | - | - | 14 | |
| DIN 3852 threaded ports on opposite side, only for through drive | ● | - | - | - | - | - | - | - | 07 |
Drive
| 003 to 010 | 018 | 028 | 045 | 071 | 100 | 140 | 180 | ||||||
| 12 | With through-drive shaft, without hub, without intermediate flange;
fastening thread metric, with universal through drive, only port plate 22U |
- | - | - | - | ○ | ○ | ○ | ○ | 004)5) | |||
| Without through drive, only port plates 12 and 14 | ● | ● | ● | ● | ○ | ○ | ○ | ○ | N00 | ||||
| Port plate 12 and 07 | |||||||||||||
| Bride ISO 3019-1 | Moyeu pour arbre cannelé6)
Diamètre |
||||||||||||
| Diamètre | Montage7) | ||||||||||||
| 82-2 (A) | 5/8 pouce | 9T 16/32DP | ● | ● | ● | ● | - | - | - | - | K01 | ||
| 3/4 po | 11T 16/32DP | ● | ● | ● | ● | - | - | - | - | K52 | |||
| 101-2(B) | 7/8 in | 13T 16/32DP | - | - | ● | ● | - | - | - | - | K68 | ||
| 1 po | 15T 16/32DP | - | - | - | ● | - | - | - | - | K04 | |||
| Port plate 22U | |||||||||||||
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Moyeu pour arbre cannelé6)
Diamètre |
||||||||||||
| Diamètre | |||||||||||||
| 82-2 (A) | 5/8 po | 9T 16/32DP | - | - | - | - | ○ | ○ | ○ | ○ | 01 | ||
| 3/4 po | 11T 16/32DP | - | - | - | - | ○ | ○ | ○ | ○ | 52 | |||
| 101-2(B) | 7/8 in | 13T 16/32DP | - | - | - | - | ○ | ○ | ○ | ○ | 68 | ||
| 1 po | 15T 16/32DP | - | - | - | - | ○ | ○ | ○ | ○ | 04 | |||
| 1 1/4 po | 14T 12/24DP | - | - | - | - | ○ | ○ | ○ | ○ | 06 | |||
| 127-4 (C) | 1 po | 15T 16/32DP | - | - | - | - | ○ | ○ | ○ | ○ | E2 | ||
| 1 1/4 po | 14T 12/24DP | - | - | - | - | ○ | ○ | ○ | ○ | 15 | |||
| 152-4 (D) | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | 17T 12/24DP | - | - | - | - | - | ○ | ○ | ○ | 96 | ||
| 1 3/4in | 13T 8/16DP | - | - | - | - | - | ○ | ○ | ○ | 17 | |||
Connecteurs pour solénoïdes
| 13 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | 0 |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | H |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Vg maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsGiga vers 50% Vg max continu
Vg mincURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitssol mineur to 40% VGiga stepless,settings to be specified in plain text.
Vg max et Vg min limitations on through drives with port plates 12K..and 22U..can only be carried out via fixed set values, this should also be specified in plain text.
4)See data sheet 95581 universal through drive
5)When ordering sizes 071 to 180 with port plate 22, please order the relevant through drive "U"
Example: A10VZO045DR000/10R-VSD22U01
When ordering sizes 018 to 045 with port plate 12, please order the relevant through drive with "K"
Example: A10VZ0018DR000/10R-VSD12K01
6)Splined shaft according to ANSI B92.1a (splined shafts according to SAE J744)
7) Mounting holes pattern viewed on through drive with control at top
Technical data A10VZO size 3 to 45
| Taille | NG | 3 | 6 | 8 | 10 | 18 | 28 | 45 | ||
| Displacement, geometric,per revolution | Vg max | cm3 | 3.5 | 6 | 8 | 10.5 | 18 | 28 | 45 | |
| Vitesse de rotation
maximum1) |
à VGiga | |||||||||
| Suction speed operation as a pump1) | nnom | tours par minute | 3600 | 3600 | 3600 | 3600 | 3300 | 3000 | 3000 | |
| Max. speed decompression operation2) | nnom | tours par minute | 3600 | 3600 | 3600 | 3600 | 3300 | 3000 | 3000 | |
| Flux | à nnom et Vg max | qv | L/min | 12.6 | 21.6 | 28.8 | 38 | 59 | 84 | 135 |
| Puissance
Operation as a pump à nnom,Vg max |
et Δp = 250 bar | P | kW | 5 | 10 | 15 | 16 | - | - | - |
| and Δp = 315 bar | P | kW | - | - | - | - | 34 | 39 | 44 | |
| Couple | à VGiga et Δp = 250 bar | T | Rien | 14 | 24 | 32 | 42 | - | - | - |
| à VGiga and Δp = 315 bar | T | Rien | - | - | - | - | 90 | 140 | 225 | |
| à VGiga et Δp = 100 bar | T | Rien | 6 | 9 | 13 | 17 | 29 | 140 | 225 | |
| Rotary stiffness of
drive shaft |
S | c | Nm/rad | 8100 | 8100 | 8100 | 8100 | - | - | - |
| R | c | Nm/rad | - | - | - | - | 14800 | 26300 | 41000 | |
| Moment d'inertie pour le groupe rotatif | JTW | Kgm2 | 0.0006 | 0.0006 | 0.0006 | 0.0006 | 0.00093 | 0.0017 | 0.0033 | |
| Accélération angulaire maximale2)3) | α | rad/s2 | 14000 | 14000 | 14000 | 14000 | 12600 | 11200 | 9500 | |
| Volume du boîtier | V | L | 0.2 | 0.2 | 0.2 | 0.2 | 0.25 | 0.3 | 1.0 | |
| Weight without through drive (14N00, 12N00 approx.) | m | kg | 8 | 8 | 8 | 8 | 12 | 15 | 27 | |
| Weight without through drive (22U00 approx.) | m | kg | - | - | - | - | - | - | - | |
| Weight with through drive (07K.., 12K..approx.) | m | kg | 10.5 | 10.5 | 10.5 | 10.5 | 14 | 18 | 28 | |
| Weight with through drive (22U..approx.) | m | kg | - | - | - | - | - | - | - | |
Définir les caractéristiques de fonctionnement
| Flux | qv=(Vg ∙ n ∙ ηv) / 1000 | L/min |
| Couple | M=(Vg ∙ Δp) / (20 ∙ π ∙ ηhm) | Rien |
| Puissance | P=(2π ∙ M ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt) | kW |
Clé
Vg Déplacement par révolution en [cm3]
Δp Pression différentielle [bar]
n Vitesse de rotation [tr/min]
ηv Efficacité volumétrique
ηhm Efficacité hydraulico-mécanique
ηt Efficacité totale (ηt= ηv*ηhm)
1)Les valeurs sont applicables :
- At absolute pressure Pabdos = 1 bar at suction port S
- For the optimal viscosity range of vopt = 36 à 16 mm2/s
- For hydraulic fluid based on mineral oils
2)Higher values on request
3) The limit value is only valid for a single pump, multiple pump version available on request. The load capacity of the connecting parts must be considered.
Technical data A10VZO size 71 to 180
| Taille | NG | 71 | 100 | 140 | 180 | ||
| Displacement, geometric,per revolution | Vg max | cm3 | 71.1 | 100 | 140 | 180 | |
| Vitesse de rotation
maximum1) |
à VGiga | ||||||
| Suction speed operation as a pump1) | nnom | tours par minute | 2550 | 2300 | 2200 | 1800 | |
| Max. speed decompression operation2) | nnom | tours par minute | On request | ||||
| Flux | à nnom et Vg max | qv | L/min | 181 | 230 | 308 | 324 |
| Puissance
Operation as a pump à nnom,Vg max |
and Δp = 280 bar
|
P
|
kW
|
84 | 107 | 143 | 151 |
| Couple | à VGiga and Δp = 280 bar | T | Rien | 317 | 445 | 623 | 801 |
| à VGiga et Δp = 100 bar | T | Rien | 113 | 159 | 223 | 286 | |
| Rotary stiffness of
drive shaft |
S | c | Nm/rad | 8100 | 8100 | 8100 | 8100 |
| R | c | Nm/rad | - | 121142 | 169537 | 171107 | |
| Moment d'inertie pour le groupe rotatif | JTW | Kgm2 | 0.0087 | 0.0185 | 0.0276 | 0.033 | |
| Accélération angulaire maximale2)3) | α | rad/s2 | 7500 | 6200 | 5000 | 4000 | |
| Volume du boîtier | V | L | 1.6 | 2.2 | 3.0 | 2.7 | |
| Weight without through drive (12N00, 42N00 approx.) | m | kg | 36.5 | 55 | 70 | - | |
| Weight without through drive (22U00 approx.) | m | kg | 47 | 69 | 73 | 78 | |
| Weight with through drive (12K..approx.) | m | kg | - | - | - | - | |
| Weight with through drive (22U..approx.) | m | kg | 47 | 69 | 73 | 78 | |
Définir les caractéristiques de fonctionnement
| Flux | qv=(Vg ∙ n ∙ ηv) / 1000 | L/min |
| Couple | T=(Vg ∙ Δp) / (20 ∙ π ∙ ηhm) | Rien |
| Puissance | P=(2π ∙ T ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt) | kW |
Clé
Vg Déplacement par révolution en [cm3]
Δp Pression différentielle [bar]
n Vitesse de rotation [tr/min]
ηv Efficacité volumétrique
ηhm Efficacité hydraulico-mécanique
ηt Efficacité totale (ηt= ηv*ηhm)
1)Les valeurs sont applicables :
- At absolute pressure Pabdos = 1 bar at suction port S
- For the optimal viscosity range of vopt = 36 à 16 mm2/s
- For hydraulic fluid based on mineral oils
2)Higher values on request
3) The limit value is only valid for a single pump, multiple pump version available on request. The load capacity of the connecting parts must be considered.
4) With port plates 7 or 14
couples d'entrée et de transmission admissibles
| Taille | 003 to 10 | 18 | 28 | 45 | 71 | 100 | 140 | 180 | |||
| Couple d'entrée | |||||||||||
| at drive shaft, maximum2) |
S | TE max | Rien | 126 | - | - | - | - | 1104 | 1620 | 1620 |
| ∅ | in | 3/4 | - | - | - | - | 1 1/2 | 1 3/4 | 1 3/4 | ||
| R | TE max | Rien | - | 160 | 250 | 400 | 650 | - | - | - | |
| ∅ | in | - | 3/4 | 7/8 | 1 | 1 1/4 | - | - | - | ||
| Maximum through- drive torque |
S | TD max | Rien | 41 | - | - | - | - | 778 | 1266 | 1266 |
| R | TD max | Rien | - | 92 | 127 | 229 | 480 | - | - | - | |
Répartition des couples

| Couple à la première pompe | T1 |
| Couple à la deuxième pompe | T2 |
| Couple à la troisième pompe | T3 |
| Couple d'entrée | TE=T1+T2+T3 |
| TE < TE max | |
| Through-drive torque | TD=T2+T3 |
| TD < TD max |
1)Efficacité non prise en compte
2) For drive shafts with no radial force







-2.webp)