Wenzhou Prance Hydraulic Equipment Co., Ltd
MCR Radial Piston Hydraulic Motor
The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.
- Radial piston construction
- Switchable displacement described in the table
- Flange or face mounting
- Brake options require separate confirmation
PRANCE HYDRAULIC · PRODUCT SERIES
Radial piston; switchable displacement variants · Confirm the selected motor and brake circuit
The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.
Model

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Configuration review · Technical documentation · Product selection
Detalhes do Produto
- Radial piston construction
- Switchable displacement described in the table
- Flange or face mounting
- Brake options require separate confirmation
CATEGORIES: Motor de pistões, Motor de pistões radiais
MCR Features & Application
Radial piston construction
Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.
Switchable displacement described in the table
Specify the displacement range or switching arrangement and verify performance at each required setting.
Flange or face mounting
Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.
Brake options require separate confirmation
Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.
MCR Specifications
| Series / model | MCR |
|---|---|
| Product type | MCR Radial Piston Hydraulic Motor |
| Design | Radial piston; switchable displacement variants |
| Circuit / selection | Confirm the selected motor and brake circuit |
| Technical table scope | MCR10 configurations |
| Listed displacements | 780, 940, 1120, 1250 and 1340 cm³/rev |
| Displacement switching | Confirm the ordered configuration and switching conditions |
MCR Selection & Configuration
The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.
Specify full- and reduced-displacement duty separately and include required starting torque. If a brake is needed, distinguish a holding brake from a service brake and identify release pressure and control responsibility. A motor photograph cannot establish the brake option supplied.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

MCR Buying Guide
Use this sequence to prepare the MS configuration for review and quotation.
- Define starting and continuous torque, speed range and duty cycle.
- Specify available flow, work-port pressure difference and return pressure.
- Confirm the displacement setting and required behavior during starting and stopping.
- Check shaft, mounting pilot, flange, port orientation and external loads.
- Review case drainage, replenishment and any displacement control.
- Specify fluid conditions and any independent braking requirement.
- Approve the complete model, operating envelope, drawing and quantity.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

Project Inquiries
Learn more →Send your required model, quantity, application and project requirements to discuss your inquiry.
Product inquiries · Configuration review
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your MCR Application
Send the full model code, operating duty, installation details and quantity.
Request a MCR QuotationMCR Questions Before Ordering
What type of product is the MCR?
MCR Radial Piston Hydraulic Motor. Design: Radial piston; switchable displacement variants. Confirm the selected motor and brake circuit. Confirm the complete order code for the offered version.
Can a similar motor replace the MCR?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
MCR Technical Data & Documents
View MCR catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Dados técnicos
(para aplicações fora destes parâmetros, por favor consulte-nos)Geral
| Tipo | motor de pistões radiais | |||||||
| Descrição | Motor de pistões radiais multidiscos, de cilindrada comutável | |||||||
| Descrição do modelo | MCR 10… | |||||||
| Tipo de montagem | Montagem por flange; montagem de face | |||||||
| Ligações | Rosqueado ou flangeado | |||||||
| Posição de montagem | Opcional | |||||||
| Carregamento do eixo | Ver página 6 | |||||||
| Rotação | clockwise/anti-clockwise – reversible | |||||||
| Tamanho do quadro | 10 | |||||||
| Tamanho | 780 | 940 | 1120 | 1250 | 1340 | |||
| Deslocamento | V | cm3 | 780 | 940 | 1120 | 1250 | 1340 | |
| Caudal n= 100 rpm/100 bar | qV | L/min | 79 | 95 | 113,5 | 126,5 | 136,5 | |
| Binário de saída 1;7) | 1240 | 1494 | 1783 | 1990 | 2130 | |||
| -specific torque (at Δp= 100 bar) | T | Nm | ||||||
| – peak torque | T | Nm | 5134 | 6187 | 6659 | 7432 | 8027 | |
| Velocidade de saída 1;7) | 5 a 10 para um funcionamento suave, dependendo da aplicação | |||||||
| – min. speed | n | rpm | ||||||
| -vel. máx. | n | rpm | 170 | 150 | 150 | 140 | 120 | |
| – freewheeling speed | n | rpm | 400 | |||||
| Potência de saída 1;7) | 44 | 44 | 50 | 50 | 50 | |||
| – continuous power | P | kW | ||||||
| Peso | motor | m | kg | 69 | ||||
| – motor with holding brake | m | kg | 81 | |||||
| – motor with travel brake | m | kg | 92 | |||||
Hidráulico
| Pressão nominal | p | bar | 250 | ||
| Diferencial de pressão, cont. 2;6;7;8) | Δp | bar | 250 | ||
| – for mineral oil (HL, HLP) | |||||
| Diferencial de pressão, pico 3; 6;7;8) | Δp | bar | 450 | 400 | |
| - para óleo mineral (HL, HLP) | |||||
| Pressão de entrada6) Port “A” or “B” | p | bar | 470 | 420 | |
| Pressão somada 4; 6) Port “A” + “B” | p | bar | 470 | 420 | |
| Pressão de drenagem do cárter, máx. | pmax | bar | 10 | ||
| pressão de comutação (comutação de deslocamento) | bar | 10 a 30 | |||
| Fluido hidráulico 5) | Óleo mineral (HL, HLP) conforme a norma DIN 51 524 | ||||
| Gama de temperaturas do fluido hidráulico | Θ | ℃ | -20 a 80 | ||
| Gama de viscosidade | ν | mm2/s | 10 a 2000 | ||
| Limpeza dos fluidos: | Grau máximo de contaminação admissível do fluido de acordo com a norma NAS 1638 Classe 9. Recomendamos, portanto, um filtro com uma taxa de retenção mínima de β10 ≥75. | ||||
Travão
| Travão de retenção (travão de disco) | |||
| Binário de retenção | T | Nm | 7000 |
| Aliviar a pressão | p | bar | mín.15;máx.30 |
| Travão de serviço (travão de tambor) | ver tabela na página 10 | ||
Dados técnicos (valores médios, medidos a ν = 46 mm2/s e θ = 45℃)
Notas sobre dados técnicos| T = Binário em Nm | qV = Caudal de entrada em L/min | qVL = Caudal de drenagem da caixa em l/min |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsV-Os valores de binário a meio deslocamento não se aplicam a ambos os sentidos de rotação, mas apenas ao sentido de rotação preferencial marcado (ver p. 7-9) | ||
| Tamanho | 780 | 1250 | |||||||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | 0 | 25 | 50 | 100 | 150 | |||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 806 | 994 | 1049 | 1029 | 911 | 1094 | 1818 | 1726 | 1517 | 1309 |
| qV | L/min | 0,3 | 19,8 | 39,47 | 79,00 | 118,2 | 1,00 | 32,09 | 63,73 | 126,69 | 189,30 | ||
| qVL | L/min | 0,15 | 0,15 | 0,24 | 0,50 | 0,60 | 0,50 | 0,56 | 0,63 | 0,76 | 0,90 | ||
| 200 | T | Nm | 1736 | 2232 | 2282 | 2232 | 2158 | 2586 | 3669 | 3684 | 3497 | ||
| qV | L/min | 0,60 | 20,10 | 39,80 | 79,50 | 118,8 | 2,86 | 33,03 | 64,63 | 127,82 | |||
| qVL | L/min | 0,30 | 0,30 | 0,40 | 0,75 | 0,9 | 1,43 | 1,44 | 1,45 | 1,46 | |||
| 300 | T | Nm | 2604 | 3348 | 3422 | 3348 | 4178 | 5550 | 5574 | ||||
| qV | L/min | 0,80 | 20,30 | 40,00 | 80,00 | 4,08 | 34,08 | 66,16 | |||||
| qVL | L/min | 0,40 | 0,40 | 0,50 | 1,00 | 2,04 | 2,10 | 2,16 | |||||
| 400 | T | Nm | 3472 | 4464 | 4563 | 5730 | 7432 | 7416 | |||||
| qV | L/min | 1,40 | 20,90 | 40,80 | 5,68 | 35,11 | 67,35 | ||||||
| qVL | L/min | 0,70 | 0,70 | 0,90 | 2,84 | 2,92 | 3,00 | ||||||
| 450 | T | Nm | 3906 | 5022 | 5134 | ||||||||
| qV | L/min | 1,6 | 21,10 | 41,00 | |||||||||
| qVL | L/min | 0,80 | 0,8 | 1,00 | |||||||||
| Tamanho | 940 | 1340 | |||||||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | 0 | 25 | 50 | 100 | ||||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 971 | 1198 | 1264 | 1240 | 1098 | 1182 | 1964 | 1865 | 1639 | |
| qV | L/min | 1,00 | 23,80 | 47,47 | 95,00 | 142,20 | 1,00 | 34,61 | 68,78 | 136,76 | |||
| qVL | L/min | 0,15 | 0,15 | 0,24 | 0,50 | 0,60 | 0,50 | 0,56 | 0,63 | 0,76 | |||
| 200 | T | Nm | 2091 | 2690 | 2750 | 2689 | 2793 | 3962 | 3979 | 3777 | |||
| qV | L/min | 0,60 | 24,10 | 47,80 | 95,50 | 2,86 | 35,56 | 69,68 | 137,93 | ||||
| qVL | L/min | 0,30 | 0,30 | 0,40 | 0,75 | 1,43 | 1,44 | 1,45 | 1,46 | ||||
| 300 | T | Nm | 3137 | 4035 | 4124 | 4512 | 5994 | 6020 | |||||
| qV | L/min | 0,80 | 24,30 | 48,00 | 4,08 | 36,64 | 71,24 | ||||||
| qVL | L/min | 0,40 | 0,40 | 0,50 | 2,04 | 2,10 | 2,16 | ||||||
| 400 | T | Nm | 4183 | 5380 | 5500 | 6188 | 8027 | 8010 | |||||
| qV | L/min | 1,40 | 24,90 | 48,80 | 5,68 | 37,67 | 72,50 | ||||||
| qVL | L/min | 0,70 | 0,70 | 0,90 | 2,84 | 2,92 | 3,00 | ||||||
| 450 | T | Nm | 4706 | 6052 | 6187 | ||||||||
| qV | L/min | 1,60 | 25,10 | 49,00 | |||||||||
| qVL | L/min | 0,80 | 0,80 | 1,00 | |||||||||
| Tamanho | 1120 | |||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | |||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 980 | 1629 | 1547 | 1360 | 1173 |
| qV | L/min | 1,00 | 28,82 | 57,19 | 113,62 | 169,80 | ||
| qVL | L/min | 0,50 | 0,56 | 0,63 | 0,76 | 0,90 | ||
| 200 | T | Nm | 2317 | 3287 | 3301 | 3134 | ||
| qV | L/min | 2,86 | 29,76 | 58,07 | 114,71 | |||
| qVL | L/min | 1,43 | 1,44 | 1,45 | 146 | |||
| 300 | T | Nm | 3743 | 4973 | 4994 | |||
| qV | L/min | 4,08 | 30,76 | 59,49 | ||||
| qVL | L/min | 2,04 | 2,10 | 2,16 | ||||
| 400 | T | Nm | 5134 | 6660 | 6645 | |||
| qV | L/min | 5,68 | 31,76 | 60,87 | ||||
| qVL | L/min | 2,84 | 2,92 | 3,00 | ||||
Related Selection Resources
Request a MCR Quotation
Tell us your required configuration, quantity and application.
Dados técnicos
(para aplicações fora destes parâmetros, por favor consulte-nos)
Geral
| Tipo | motor de pistões radiais | |||||||
| Descrição | Motor de pistões radiais multidiscos, de cilindrada comutável | |||||||
| Descrição do modelo | MCR 10... | |||||||
| Tipo de montagem | Montagem por flange; montagem de face | |||||||
| Ligações | Rosqueado ou flangeado | |||||||
| Posição de montagem | Opcional | |||||||
| Carregamento do eixo | Ver página 6 | |||||||
| Rotação | sentido horário/sentido anti-horário - reversível | |||||||
| Tamanho do quadro | 10 | |||||||
| Tamanho | 780 | 940 | 1120 | 1250 | 1340 | |||
| Deslocamento | V | cm3 | 780 | 940 | 1120 | 1250 | 1340 | |
| Caudal n= 100 rpm/100 bar | qV | L/min | 79 | 95 | 113,5 | 126,5 | 136,5 | |
| Binário de saída 1;7) | 1240 | 1494 | 1783 | 1990 | 2130 | |||
| - binário específico (a Δp= 100 bar) |
T | Nm | ||||||
| - binário máximo | T | Nm | 5134 | 6187 | 6659 | 7432 | 8027 | |
| Velocidade de saída 1;7) | 5 a 10 para um funcionamento suave, dependendo da aplicação | |||||||
| - vel. mín. | n | rpm | ||||||
| -vel. máx. | n | rpm | 170 | 150 | 150 | 140 | 120 | |
| velocidade em roda livre | n | rpm | 400 | |||||
| Potência de saída 1;7) | 44 | 44 | 50 | 50 | 50 | |||
| - potência contínua | P | kW | ||||||
| Peso | motor | m | kg | 69 | ||||
| - motor com travão de retenção | m | kg | 81 | |||||
| - motor com travão de translação | m | kg | 92 | |||||
Hidráulico
| Pressão nominal | p | bar | 250 | ||
| Diferencial de pressão, cont. 2;6;7;8) | Δp | bar | 250 | ||
| - para óleo mineral (HL, HLP) | |||||
| Diferencial de pressão, pico 3; 6;7;8) | Δp | bar | 450 | 400 | |
| - para óleo mineral (HL, HLP) | |||||
| Pressão de entrada6) Porto "A" ou "B" | p | bar | 470 | 420 | |
| Pressão somada 4; 6Porta "A" + "B" | p | bar | 470 | 420 | |
| Pressão de drenagem do cárter, máx. | pmax | bar | 10 | ||
| pressão de comutação (comutação de deslocamento) | bar | 10 a 30 | |||
| Fluido hidráulico 5) | Óleo mineral (HL, HLP) conforme a norma DIN 51 524 | ||||
| Gama de temperaturas do fluido hidráulico | Θ | ℃ | -20 a 80 | ||
| Gama de viscosidade | ν | mm2/s | 10 a 2000 | ||
| Limpeza dos fluidos: | Grau máximo de contaminação admissível do fluido de acordo com a norma NAS 1638 Classe 9. Recomendamos, portanto, um filtro com uma taxa de retenção mínima de β10 ≥75. | ||||
Travão
| Travão de retenção (travão de disco) | |||
| Binário de retenção | T | Nm | 7000 |
| Aliviar a pressão | p | bar | mín.15;máx.30 |
| Travão de serviço (travão de tambor) | ver tabela na página 10 | ||
Os valores indicados aplicam-se após um período de rodagem de 100 horas
2) Funcionamento contínuo
3) Os valores de pico podem ocorrer por uma duração máxima de apenas um segundo num minuto de funcionamento
4) Recomendamos Pmin = 15 bar na linha de retorno
5) Fluidos ecológicos HETG, HEPG, HEES para RE 90 221
6) Ao operar motores em série, consulte o nosso gabinete técnico
7)⚠ Aviso: Ao colocar o motor a funcionar (mínimo de 20 horas), tenha em atenção que: o motor não deve funcionar sem carga a uma velocidade superior a 50 %.
8) Para extremidade de eixo único "L60", pressão diferencial máx. admissível Δp = 250 bar
Dados técnicos (valores médios, medidos a ν = 46 mm2/s e θ = 45℃)
Notas sobre dados técnicos
| T = Binário em Nm | qV = Caudal de entrada em L/min | qVL = Caudal de drenagem da caixa em l/min |
| -Todos os binários aplicam-se a motores em rodagem (ver nota p. 4, nota de rodapé 7) -Para o modo de "meia cilindrada", multiplicar o binário e o qV-valores em 0,5. -Os valores de binário a meio deslocamento não se aplicam a ambos os sentidos de rotação, mas apenas ao sentido de rotação preferencial marcado (ver p. 7-9) |
||
| Tamanho | 780 | 1250 | |||||||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | 0 | 25 | 50 | 100 | 150 | |||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 806 | 994 | 1049 | 1029 | 911 | 1094 | 1818 | 1726 | 1517 | 1309 |
| qV | L/min | 0,3 | 19,8 | 39,47 | 79,00 | 118,2 | 1,00 | 32,09 | 63,73 | 126,69 | 189,30 | ||
| qVL | L/min | 0,15 | 0,15 | 0,24 | 0,50 | 0,60 | 0,50 | 0,56 | 0,63 | 0,76 | 0,90 | ||
| 200 | T | Nm | 1736 | 2232 | 2282 | 2232 | 2158 | 2586 | 3669 | 3684 | 3497 | ||
| qV | L/min | 0,60 | 20,10 | 39,80 | 79,50 | 118,8 | 2,86 | 33,03 | 64,63 | 127,82 | |||
| qVL | L/min | 0,30 | 0,30 | 0,40 | 0,75 | 0,9 | 1,43 | 1,44 | 1,45 | 1,46 | |||
| 300 | T | Nm | 2604 | 3348 | 3422 | 3348 | 4178 | 5550 | 5574 | ||||
| qV | L/min | 0,80 | 20,30 | 40,00 | 80,00 | 4,08 | 34,08 | 66,16 | |||||
| qVL | L/min | 0,40 | 0,40 | 0,50 | 1,00 | 2,04 | 2,10 | 2,16 | |||||
| 400 | T | Nm | 3472 | 4464 | 4563 | 5730 | 7432 | 7416 | |||||
| qV | L/min | 1,40 | 20,90 | 40,80 | 5,68 | 35,11 | 67,35 | ||||||
| qVL | L/min | 0,70 | 0,70 | 0,90 | 2,84 | 2,92 | 3,00 | ||||||
| 450 | T | Nm | 3906 | 5022 | 5134 | ||||||||
| qV | L/min | 1,6 | 21,10 | 41,00 | |||||||||
| qVL | L/min | 0,80 | 0,8 | 1,00 | |||||||||
| Tamanho | 940 | 1340 | |||||||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | 0 | 25 | 50 | 100 | ||||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 971 | 1198 | 1264 | 1240 | 1098 | 1182 | 1964 | 1865 | 1639 | |
| qV | L/min | 1,00 | 23,80 | 47,47 | 95,00 | 142,20 | 1,00 | 34,61 | 68,78 | 136,76 | |||
| qVL | L/min | 0,15 | 0,15 | 0,24 | 0,50 | 0,60 | 0,50 | 0,56 | 0,63 | 0,76 | |||
| 200 | T | Nm | 2091 | 2690 | 2750 | 2689 | 2793 | 3962 | 3979 | 3777 | |||
| qV | L/min | 0,60 | 24,10 | 47,80 | 95,50 | 2,86 | 35,56 | 69,68 | 137,93 | ||||
| qVL | L/min | 0,30 | 0,30 | 0,40 | 0,75 | 1,43 | 1,44 | 1,45 | 1,46 | ||||
| 300 | T | Nm | 3137 | 4035 | 4124 | 4512 | 5994 | 6020 | |||||
| qV | L/min | 0,80 | 24,30 | 48,00 | 4,08 | 36,64 | 71,24 | ||||||
| qVL | L/min | 0,40 | 0,40 | 0,50 | 2,04 | 2,10 | 2,16 | ||||||
| 400 | T | Nm | 4183 | 5380 | 5500 | 6188 | 8027 | 8010 | |||||
| qV | L/min | 1,40 | 24,90 | 48,80 | 5,68 | 37,67 | 72,50 | ||||||
| qVL | L/min | 0,70 | 0,70 | 0,90 | 2,84 | 2,92 | 3,00 | ||||||
| 450 | T | Nm | 4706 | 6052 | 6187 | ||||||||
| qV | L/min | 1,60 | 25,10 | 49,00 | |||||||||
| qVL | L/min | 0,80 | 0,80 | 1,00 | |||||||||
| Tamanho | 1120 | |||||||
| Velocidade n em rpm | 0 | 25 | 50 | 100 | 150 | |||
| Diferencial de pressão Δp em bar | 100 | T | Nm | 980 | 1629 | 1547 | 1360 | 1173 |
| qV | L/min | 1,00 | 28,82 | 57,19 | 113,62 | 169,80 | ||
| qVL | L/min | 0,50 | 0,56 | 0,63 | 0,76 | 0,90 | ||
| 200 | T | Nm | 2317 | 3287 | 3301 | 3134 | ||
| qV | L/min | 2,86 | 29,76 | 58,07 | 114,71 | |||
| qVL | L/min | 1,43 | 1,44 | 1,45 | 146 | |||
| 300 | T | Nm | 3743 | 4973 | 4994 | |||
| qV | L/min | 4,08 | 30,76 | 59,49 | ||||
| qVL | L/min | 2,04 | 2,10 | 2,16 | ||||
| 400 | T | Nm | 5134 | 6660 | 6645 | |||
| qV | L/min | 5,68 | 31,76 | 60,87 | ||||
| qVL | L/min | 2,84 | 2,92 | 3,00 | ||||







