MCR Radial Piston Hydraulic Motor

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

  • Radial piston construction
  • Switchable displacement described in the table
  • Flange or face mounting
  • Brake options require separate confirmation

PRANCE HYDRAULIC · PRODUCT SERIES

MCR Radial Piston Hydraulic Motor

Radial piston; switchable displacement variants · Confirm the selected motor and brake circuit

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

Model

✓MCR original product photograph
MCRRadial piston; switchable displacement variants
Request a QuotationTechnische Daten & Datenblatt anzeigen

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Configuration review · Technical documentation · Product selection

Produktdetails

  • Radial piston construction
  • Switchable displacement described in the table
  • Flange or face mounting
  • Brake options require separate confirmation

CATEGORIES: Kolbenmotor, Radialkolbenmotor

MCR Features & Application

Radial piston construction

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

Switchable displacement described in the table

Specify the displacement range or switching arrangement and verify performance at each required setting.

Flange or face mounting

Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.

Brake options require separate confirmation

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

MCR Specifications

Series / modelMCR
Product typeMCR Radial Piston Hydraulic Motor
DesignRadial piston; switchable displacement variants
Circuit / selectionConfirm the selected motor and brake circuit
Technical table scopeMCR10 configurations
Listed displacements780, 940, 1120, 1250 and 1340 cm³/rev
Displacement switchingConfirm the ordered configuration and switching conditions

MCR Selection & Configuration

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

Specify full- and reduced-displacement duty separately and include required starting torque. If a brake is needed, distinguish a holding brake from a service brake and identify release pressure and control responsibility. A motor photograph cannot establish the brake option supplied.

MCR original product view

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

MCR Buying Guide

Use this sequence to prepare the MS configuration for review and quotation.

  1. Define starting and continuous torque, speed range and duty cycle.
  2. Specify available flow, work-port pressure difference and return pressure.
  3. Confirm the displacement setting and required behavior during starting and stopping.
  4. Check shaft, mounting pilot, flange, port orientation and external loads.
  5. Review case drainage, replenishment and any displacement control.
  6. Specify fluid conditions and any independent braking requirement.
  7. Approve the complete model, operating envelope, drawing and quantity.
MCR original product photograph for installation review

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Project Inquiries

Learn more →

Send your required model, quantity, application and project requirements to discuss your inquiry.


Product inquiries · Configuration review

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your MCR Application

Send the full model code, operating duty, installation details and quantity.

Request a MCR Quotation

MCR Questions Before Ordering

What type of product is the MCR?

MCR Radial Piston Hydraulic Motor. Design: Radial piston; switchable displacement variants. Confirm the selected motor and brake circuit. Confirm the complete order code for the offered version.

Can a similar motor replace the MCR?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

MCR Technical Data & Documents

View MCR catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Technische Daten

(für Anwendungen außerhalb dieser Parameter sprechen Sie uns bitte an)

Allgemein

Typ Radialkolbenmotor
Beschreibung Radialkolben-Lamellenmotor, schaltbares Hubvolumen
Modellbeschreibung MCR 10…
Montageart Flanschmontage; Frontmontage
Verbindungen Mit Gewinde oder geflanscht
Montageposition Optional
Schachtbeladung Siehe Seite 6
Drehung clockwise/anti-clockwise – reversible
Rahmengröße 10
Größe 780 940 1120 1250 1340
Verschiebung V cm3 780 940 1120 1250 1340
Förderstrom n= 100 U/min / 100 bar qV l/min 79 95 113,5 126,5 136,5
Abtriebsdrehmoment 1;7) 1240 1494 1783 1990 2130
-specific torque (at Δp= 100 bar) T Machs gut
– peak torque T Machs gut 5134 6187 6659 7432 8027
Ausgabegeschwindigkeit 1;7) 5 bis 10 für einen ruhigen Lauf, je nach Anwendung
– min. speed n U/min
- max. Geschwindigkeit n U/min 170 150 150 140 120
– freewheeling speed n U/min 400
Ausgangsleistung 1;7) 44 44 50 50 50
– continuous power P kW
Gewicht -motor m kg 69
– motor with holding brake m kg 81
– motor with travel brake m kg 92

Hydraulisch

Nenndruck p Bar 250
Druckdifferenz, Forts. 2;6;7;8) Δp Bar 250
– for mineral oil (HL, HLP)
Druckdifferenz, maximaler 3; 6;7;8) Δp Bar 450 400
- für Mineralöl (HL, HLP)
Eingangsdruck6)  Port “A” or “B” p Bar 470 420
Summierter Druck 4; 6) Port “A” + “B” p Bar 470 420
Gehäusedruck, max. Pmax Bar 10
Schaltverdrängung Bar 10 bis 30
Hydraulikflüssigkeit 5) Mineralöl (HL, HLP) nach DIN 51 524
Temperaturbereich der Hydraulikflüssigkeit Θ ℃ -20 bis 80
Viskositätsbereich ν mm2/s 10 bis 2000
Flüssigkeitssauberkeit Maximal zulässiger Verschmutzungsgrad des Fluids nach NAS 1638 Klasse 9. Wir empfehlen daher einen Filter mit einer minimalen Rückhaltequote von β10 ≥ 75.

Bremse

Haltemuse (Scheibenbremse)
Haltemoment T Machs gut 7000
Druck ablassen p Bar mind. 15; max. 30
Fahrbremse (Trommelbremse) siehe Tabelle Seite 10
1)The values given apply after 100 hours run-in time 2) Continuous operation 3) Peak values may occur for a maximum duration of one second only within an operating minute 4) We recommend Pmin. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits WarnungcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsp = 250 bar

Technische Daten (Mittelwerte, gemessen bei ν = 46 mm2/s und θ = 45℃)

Hinweise zu technischen Daten
T = Drehmoment in Nm qV = Zulauf in L/min qVL = Gehäusedrainagestrom in L/min
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsV-Die Drehmomentwerte bei halbem Hub gelten nicht für beide Drehrichtungen, sondern nur für die markierte bevorzugte Drehrichtung (siehe S. 7–9)
Größe 780 1250
Drehzahl n in U/min 0 25 50 100 150 0 25 50 100 150
Druckdifferenz Δp in bar 100 T Machs gut 806 994 1049 1029 911 1094 1818 1726 1517 1309
qV l/min 0,3 19,8 39,47 79,00 118,2 1,00 32,09 63,73 126,69 189,30
qVL l/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76 0,90
200 T Machs gut 1736 2232 2282 2232 2158 2586 3669 3684 3497
qV l/min 0,60 20,10 39,80 79,50 118,8 2,86 33,03 64,63 127,82
qVL l/min 0,30 0,30 0,40 0,75 0,9 1,43 1,44 1,45 1,46
300 T Machs gut 2604 3348 3422 3348 4178 5550 5574
qV l/min 0,80 20,30 40,00 80,00 4,08 34,08 66,16
qVL l/min 0,40 0,40 0,50 1,00 2,04 2,10 2,16
400 T Machs gut 3472 4464 4563 5730 7432 7416
qV l/min 1,40 20,90 40,80 5,68 35,11 67,35
qVL l/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Machs gut 3906 5022 5134
qV l/min 1,6 21,10 41,00
qVL l/min 0,80 0,8 1,00
Größe 940 1340
Drehzahl n in U/min 0 25 50 100 150 0 25 50 100
Druckdifferenz Δp in bar 100 T Machs gut 971 1198 1264 1240 1098 1182 1964 1865 1639
qV l/min 1,00 23,80 47,47 95,00 142,20 1,00 34,61 68,78 136,76
qVL l/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76
200 T Machs gut 2091 2690 2750 2689 2793 3962 3979 3777
qV l/min 0,60 24,10 47,80 95,50 2,86 35,56 69,68 137,93
qVL l/min 0,30 0,30 0,40 0,75 1,43 1,44 1,45 1,46
300 T Machs gut 3137 4035 4124 4512 5994 6020
qV l/min 0,80 24,30 48,00 4,08 36,64 71,24
qVL l/min 0,40 0,40 0,50 2,04 2,10 2,16
400 T Machs gut 4183 5380 5500 6188 8027 8010
qV l/min 1,40 24,90 48,80 5,68 37,67 72,50
qVL l/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Machs gut 4706 6052 6187
qV l/min 1,60 25,10 49,00
qVL l/min 0,80 0,80 1,00
Größe 1120
Drehzahl n in U/min 0 25 50 100 150
Druckdifferenz Δp in bar 100 T Machs gut 980 1629 1547 1360 1173
qV l/min 1,00 28,82 57,19 113,62 169,80
qVL l/min 0,50 0,56 0,63 0,76 0,90
200 T Machs gut 2317 3287 3301 3134
qV l/min 2,86 29,76 58,07 114,71
qVL l/min 1,43 1,44 1,45 146
300 T Machs gut 3743 4973 4994
qV l/min 4,08 30,76 59,49
qVL l/min 2,04 2,10 2,16
400 T Machs gut 5134 6660 6645
qV l/min 5,68 31,76 60,87
qVL l/min 2,84 2,92 3,00

Request a MCR Quotation

Tell us your required configuration, quantity and application.

Kontaktformular-Demo
MCR original product photograph

Technische Daten

(für Anwendungen außerhalb dieser Parameter sprechen Sie uns bitte an)

Allgemein

Typ Radialkolbenmotor
Beschreibung Radialkolben-Lamellenmotor, schaltbares Hubvolumen
Modellbeschreibung MCR 10...
Montageart Flanschmontage; Frontmontage
Verbindungen Mit Gewinde oder geflanscht
Montageposition Optional
Schachtbeladung Siehe Seite 6
Drehung im Uhrzeigersinn / gegen den Uhrzeigersinn – reversibel
Rahmengröße 10
Größe 780 940 1120 1250 1340
Verschiebung V cm3 780 940 1120 1250 1340
Förderstrom n= 100 U/min / 100 bar qV l/min 79 95 113,5 126,5 136,5
Abtriebsdrehmoment 1;7) 1240 1494 1783 1990 2130
spezifisches Drehmoment
(bei Δp = 100 bar)
T Machs gut
- Spitzenmoment T Machs gut 5134 6187 6659 7432 8027
Ausgabegeschwindigkeit 1;7) 5 bis 10 für einen ruhigen Lauf, je nach Anwendung
- Mindestgeschwindigkeit n U/min
- max. Geschwindigkeit n U/min 170 150 150 140 120
- Leerlaufdrehzahl n U/min 400
Ausgangsleistung 1;7) 44 44 50 50 50
- Dauerleistung P kW
Gewicht -motor m kg 69
- Motor mit Haltebremse m kg 81
- Motor mit Haltebremse m kg 92

Hydraulisch

Nenndruck p Bar 250
Druckdifferenz, Forts. 2;6;7;8) Δp Bar 250
- für Mineralöl (HL, HLP)
Druckdifferenz, maximaler 3; 6;7;8) Δp Bar 450 400
- für Mineralöl (HL, HLP)
Eingangsdruck6Port "A" oder "B" p Bar 470 420
Summierter Druck 4; 6Port "A" + "B" p Bar 470 420
Gehäusedruck, max. Pmax Bar 10
Schaltverdrängung Bar 10 bis 30
Hydraulikflüssigkeit 5) Mineralöl (HL, HLP) nach DIN 51 524
Temperaturbereich der Hydraulikflüssigkeit Θ ℃ -20 bis 80
Viskositätsbereich ν mm2/s 10 bis 2000
Flüssigkeitssauberkeit Maximal zulässiger Verschmutzungsgrad des Fluids nach NAS 1638 Klasse 9. Wir empfehlen daher einen Filter mit einer minimalen Rückhaltequote von β10 ≥ 75.

Bremse

Haltemuse (Scheibenbremse)
Haltemoment T Machs gut 7000
Druck ablassen p Bar mind. 15; max. 30
Fahrbremse (Trommelbremse) siehe Tabelle Seite 10

Die angegebenen Werte gelten nach 100 Stunden Einlaufzeit

2) Dauerbetrieb

3) Spitzenwerte dürfen innerhalb einer Betriebsminute für eine Höchstdauer von nur einer Sekunde auftreten

4) Wir empfehlen Pmin. = 15 bar in der Rücklaufleitung

5) Umweltfreundliche Flüssigkeiten HETG, HEPG, HEES nach RE 90 221

6) Bei Betrieb von Motoren in Reihe wenden Sie sich bitte an unser technisches Büro

7)⚠ Warnung: Beim Einlaufen des Motors (mindestens 20 Stunden) ist zu beachten, dass der Motor im Leerlauf nicht mit mehr als 50 % der maximalen Drehzahl betrieben werden darf.

8) Für einzelnes Wellenende "L60" max. zulässiger Druckunterschied Δp = 250 bar

Technische Daten (Mittelwerte, gemessen bei ν = 46 mm2/s und θ = 45℃)

Hinweise zu technischen Daten

T = Drehmoment in Nm qV = Zulauf in L/min qVL = Gehäusedrainagestrom in L/min
-Alle Drehmomente gelten für Einlaufmotoren (siehe Hinweis S. 4, Fußnote 7)
- Für den Modus "halber Hubraum" Drehmoment- und q multiplizierenV-Werte um 0,5.
-Die Drehmomentwerte bei halbem Hub gelten nicht für beide Drehrichtungen, sondern nur für die markierte bevorzugte Drehrichtung (siehe S. 7–9)
Größe 780 1250
Drehzahl n in U/min 0 25 50 100 150 0 25 50 100 150
Druckdifferenz Δp in bar 100 T Machs gut 806 994 1049 1029 911 1094 1818 1726 1517 1309
qV l/min 0,3 19,8 39,47 79,00 118,2 1,00 32,09 63,73 126,69 189,30
qVL l/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76 0,90
200 T Machs gut 1736 2232 2282 2232 2158 2586 3669 3684 3497
qV l/min 0,60 20,10 39,80 79,50 118,8 2,86 33,03 64,63 127,82
qVL l/min 0,30 0,30 0,40 0,75 0,9 1,43 1,44 1,45 1,46
300 T Machs gut 2604 3348 3422 3348 4178 5550 5574
qV l/min 0,80 20,30 40,00 80,00 4,08 34,08 66,16
qVL l/min 0,40 0,40 0,50 1,00 2,04 2,10 2,16
400 T Machs gut 3472 4464 4563 5730 7432 7416
qV l/min 1,40 20,90 40,80 5,68 35,11 67,35
qVL l/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Machs gut 3906 5022 5134
qV l/min 1,6 21,10 41,00
qVL l/min 0,80 0,8 1,00
Größe 940 1340
Drehzahl n in U/min 0 25 50 100 150 0 25 50 100
Druckdifferenz Δp in bar 100 T Machs gut 971 1198 1264 1240 1098 1182 1964 1865 1639
qV l/min 1,00 23,80 47,47 95,00 142,20 1,00 34,61 68,78 136,76
qVL l/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76
200 T Machs gut 2091 2690 2750 2689 2793 3962 3979 3777
qV l/min 0,60 24,10 47,80 95,50 2,86 35,56 69,68 137,93
qVL l/min 0,30 0,30 0,40 0,75 1,43 1,44 1,45 1,46
300 T Machs gut 3137 4035 4124 4512 5994 6020
qV l/min 0,80 24,30 48,00 4,08 36,64 71,24
qVL l/min 0,40 0,40 0,50 2,04 2,10 2,16
400 T Machs gut 4183 5380 5500 6188 8027 8010
qV l/min 1,40 24,90 48,80 5,68 37,67 72,50
qVL l/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Machs gut 4706 6052 6187
qV l/min 1,60 25,10 49,00
qVL l/min 0,80 0,80 1,00
Größe 1120
Drehzahl n in U/min 0 25 50 100 150
Druckdifferenz Δp in bar 100 T Machs gut 980 1629 1547 1360 1173
qV l/min 1,00 28,82 57,19 113,62 169,80
qVL l/min 0,50 0,56 0,63 0,76 0,90
200 T Machs gut 2317 3287 3301 3134
qV l/min 2,86 29,76 58,07 114,71
qVL l/min 1,43 1,44 1,45 146
300 T Machs gut 3743 4973 4994
qV l/min 4,08 30,76 59,49
qVL l/min 2,04 2,10 2,16
400 T Machs gut 5134 6660 6645
qV l/min 5,68 31,76 60,87
qVL l/min 2,84 2,92 3,00