MCR Radial Piston Hydraulic Motor

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

  • Radial piston construction
  • Switchable displacement described in the table
  • Flange or face mounting
  • Brake options require separate confirmation

PRANCE HYDRAULIC · PRODUCT SERIES

MCR Radial Piston Hydraulic Motor

Radial piston; switchable displacement variants · Confirm the selected motor and brake circuit

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

Model

✓MCR original product photograph
MCRRadial piston; switchable displacement variants
Request a QuotationVer Datos Técnicos y Ficha Técnica

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Configuration review · Technical documentation · Product selection

Detalles del producto

  • Radial piston construction
  • Switchable displacement described in the table
  • Flange or face mounting
  • Brake options require separate confirmation

CATEGORIES: Motor de pistón, Motor de pistones radiales

MCR Features & Application

Radial piston construction

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

Switchable displacement described in the table

Specify the displacement range or switching arrangement and verify performance at each required setting.

Flange or face mounting

Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.

Brake options require separate confirmation

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

MCR Specifications

Series / modelMCR
Product typeMCR Radial Piston Hydraulic Motor
DiseñoRadial piston; switchable displacement variants
Circuit / selectionConfirm the selected motor and brake circuit
Technical table scopeMCR10 configurations
Listed displacements780, 940, 1120, 1250 and 1340 cm³/rev
Displacement switchingConfirm the ordered configuration and switching conditions

MCR Selection & Configuration

The MCR radial piston motor is offered with switchable displacement and several mounting or brake arrangements. The technical data specifically describes MCR10 configurations; those figures must not be applied to every MCR frame.

Specify full- and reduced-displacement duty separately and include required starting torque. If a brake is needed, distinguish a holding brake from a service brake and identify release pressure and control responsibility. A motor photograph cannot establish the brake option supplied.

MCR original product view

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

MCR Buying Guide

Use this sequence to prepare the MS configuration for review and quotation.

  1. Define starting and continuous torque, speed range and duty cycle.
  2. Specify available flow, work-port pressure difference and return pressure.
  3. Confirm the displacement setting and required behavior during starting and stopping.
  4. Check shaft, mounting pilot, flange, port orientation and external loads.
  5. Review case drainage, replenishment and any displacement control.
  6. Specify fluid conditions and any independent braking requirement.
  7. Approve the complete model, operating envelope, drawing and quantity.
MCR original product photograph for installation review

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Project Inquiries

Learn more →

Send your required model, quantity, application and project requirements to discuss your inquiry.


Product inquiries · Configuration review

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your MCR Application

Send the full model code, operating duty, installation details and quantity.

Request a MCR Quotation

MCR Questions Before Ordering

What type of product is the MCR?

MCR Radial Piston Hydraulic Motor. Design: Radial piston; switchable displacement variants. Confirm the selected motor and brake circuit. Confirm the complete order code for the offered version.

Can a similar motor replace the MCR?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

MCR Technical Data & Documents

View MCR catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Datos técnicos

(para aplicaciones fuera de estos parámetros, consúltenos)

General

Tipo Motor de pistones radiales
Descripción Motor de pistones radiales de discos múltiples, cilindrada conmutable
Descripción del modelo MCR 10…
Tipo de montaje Montaje por brida; montaje frontal
Conexiones Roscado o bridado
Posición de montaje Opcional
Carga del eje Ver la página 6
Rotación clockwise/anti-clockwise – reversible
Tamaño del marco 10
Tamaño 780 940 1120 1250 1340
Desplazamiento V cm3 780 940 1120 1250 1340
Caudal n= 100 rpm/100 bar qV L/min 79 95 113,5 126,5 136,5
Par de salida 1;7) 1240 1494 1783 1990 2130
-specific torque (at Δp= 100 bar) T Nm
– peak torque T Nm 5134 6187 6659 7432 8027
Velocidad de salida 1;7) de 5 a 10 para un funcionamiento suave, según la aplicación
– min. speed n rpm
-máx. velocidad n rpm 170 150 150 140 120
– freewheeling speed n rpm 400
Potencia de salida 1;7) 44 44 50 50 50
– continuous power P kW
Peso -motor m kg 69
– motor with holding brake m kg 81
– motor with travel brake m kg 92

Hidráulico

Presión nominal p bar 250
Diferencial de presión, cont. 2;6;7;8) Δp bar 250
– for mineral oil (HL, HLP)
Diferencial de presión, pico 3; 6;7;8) Δp bar 450 400
-para aceite mineral (HL, HLP)
Presión de entrada6)  Port “A” or “B” p bar 470 420
Presión sumada 4; 6) Port “A” + “B” p bar 470 420
Presión de drenaje de caja, máx. pmax bar 10
Presión de conmutación (conmutación por desplazamiento) bar 10 a 30
Fluido hidráulico 5) Aceite mineral (HL, HLP) según DIN 51 524
Rango de temperatura del fluido hidráulico Θ ℃ -20 a 80
Rango de viscosidad ν mm2/s 10 a 2000
Limpieza del fluido: Grado máximo de contaminación admisible del fluido según la clase 9 de la norma NAS 1638. Por lo tanto, recomendamos un filtro con una tasa de retención mínima de β10 ≥75.

Freno

Freno de retención (freno de disco)
Par de retención T Nm 7000
Liberar presión p bar mín. 15; máx. 30
Freno de desplazamiento (freno de tambor) ver tabla página 10
1)The values given apply after 100 hours run-in time 2) Continuous operation 3) Peak values may occur for a maximum duration of one second only within an operating minute 4) We recommend Pmín cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits AdvertenciacURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsp = 250 bar

Datos técnicos (valores medios, medidos a ν = 46 mm2/s y θ = 45℃)

Notas sobre datos técnicos
T = Par en Nm qV = Flujo de entrada en L/min qVL = Flujo de drenaje de la caja en L/min
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsV-Los valores de par a medio desplazamiento no se aplican a ambos sentidos de giro, sino únicamente al sentido de giro preferente marcado (véanse las páginas 7 a 9)
Tamaño 780 1250
Velocidad n en rpm 0 25 50 100 150 0 25 50 100 150
Diferencial de presión Δp en bar 100 T Nm 806 994 1049 1029 911 1094 1818 1726 1517 1309
qV L/min 0,3 19,8 39,47 79,00 118,2 1,00 32,09 63,73 126,69 189,30
qVL L/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76 0,90
200 T Nm 1736 2232 2282 2232 2158 2586 3669 3684 3497
qV L/min 0,60 20,10 39,80 79,50 118,8 2,86 33,03 64,63 127,82
qVL L/min 0,30 0,30 0,40 0,75 0,9 1,43 1,44 1,45 1,46
300 T Nm 2604 3348 3422 3348 4178 5550 5574
qV L/min 0,80 20,30 40,00 80,00 4,08 34,08 66,16
qVL L/min 0,40 0,40 0,50 1,00 2,04 2,10 2,16
400 T Nm 3472 4464 4563 5730 7432 7416
qV L/min 1,40 20,90 40,80 5,68 35,11 67,35
qVL L/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Nm 3906 5022 5134
qV L/min 1,6 21,10 41,00
qVL L/min 0,80 0,8 1,00
Tamaño 940 1340
Velocidad n en rpm 0 25 50 100 150 0 25 50 100
Diferencial de presión Δp en bar 100 T Nm 971 1198 1264 1240 1098 1182 1964 1865 1639
qV L/min 1,00 23,80 47,47 95,00 142,20 1,00 34,61 68,78 136,76
qVL L/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76
200 T Nm 2091 2690 2750 2689 2793 3962 3979 3777
qV L/min 0,60 24,10 47,80 95,50 2,86 35,56 69,68 137,93
qVL L/min 0,30 0,30 0,40 0,75 1,43 1,44 1,45 1,46
300 T Nm 3137 4035 4124 4512 5994 6020
qV L/min 0,80 24,30 48,00 4,08 36,64 71,24
qVL L/min 0,40 0,40 0,50 2,04 2,10 2,16
400 T Nm 4183 5380 5500 6188 8027 8010
qV L/min 1,40 24,90 48,80 5,68 37,67 72,50
qVL L/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Nm 4706 6052 6187
qV L/min 1,60 25,10 49,00
qVL L/min 0,80 0,80 1,00
Tamaño 1120
Velocidad n en rpm 0 25 50 100 150
Diferencial de presión Δp en bar 100 T Nm 980 1629 1547 1360 1173
qV L/min 1,00 28,82 57,19 113,62 169,80
qVL L/min 0,50 0,56 0,63 0,76 0,90
200 T Nm 2317 3287 3301 3134
qV L/min 2,86 29,76 58,07 114,71
qVL L/min 1,43 1,44 1,45 146
300 T Nm 3743 4973 4994
qV L/min 4,08 30,76 59,49
qVL L/min 2,04 2,10 2,16
400 T Nm 5134 6660 6645
qV L/min 5,68 31,76 60,87
qVL L/min 2,84 2,92 3,00

Request a MCR Quotation

Tell us your required configuration, quantity and application.

Demostración de formulario de contacto
MCR original product photograph

Datos técnicos

(para aplicaciones fuera de estos parámetros, consúltenos)

General

Tipo Motor de pistones radiales
Descripción Motor de pistones radiales de discos múltiples, cilindrada conmutable
Descripción del modelo MCR 10...
Tipo de montaje Montaje por brida; montaje frontal
Conexiones Roscado o bridado
Posición de montaje Opcional
Carga del eje Ver la página 6
Rotación en sentido horario / en sentido antihorario - reversible
Tamaño del marco 10
Tamaño 780 940 1120 1250 1340
Desplazamiento V cm3 780 940 1120 1250 1340
Caudal n= 100 rpm/100 bar qV L/min 79 95 113,5 126,5 136,5
Par de salida 1;7) 1240 1494 1783 1990 2130
-par específico
(a Δp = 100 bar)
T Nm
- par motor máximo T Nm 5134 6187 6659 7432 8027
Velocidad de salida 1;7) de 5 a 10 para un funcionamiento suave, según la aplicación
- mín. velocidad n rpm
-máx. velocidad n rpm 170 150 150 140 120
- velocidad de giro libre n rpm 400
Potencia de salida 1;7) 44 44 50 50 50
- potencia continua P kW
Peso -motor m kg 69
- motor con freno de retención m kg 81
- motor con freno de desplazamiento m kg 92

Hidráulico

Presión nominal p bar 250
Diferencial de presión, cont. 2;6;7;8) Δp bar 250
- para aceite mineral (HL, HLP)
Diferencial de presión, pico 3; 6;7;8) Δp bar 450 400
-para aceite mineral (HL, HLP)
Presión de entrada6) Puerto "A" o "B" p bar 470 420
Presión sumada 4; 6Puerto "A" + "B" p bar 470 420
Presión de drenaje de caja, máx. pmax bar 10
Presión de conmutación (conmutación por desplazamiento) bar 10 a 30
Fluido hidráulico 5) Aceite mineral (HL, HLP) según DIN 51 524
Rango de temperatura del fluido hidráulico Θ ℃ -20 a 80
Rango de viscosidad ν mm2/s 10 a 2000
Limpieza del fluido: Grado máximo de contaminación admisible del fluido según la clase 9 de la norma NAS 1638. Por lo tanto, recomendamos un filtro con una tasa de retención mínima de β10 ≥75.

Freno

Freno de retención (freno de disco)
Par de retención T Nm 7000
Liberar presión p bar mín. 15; máx. 30
Freno de desplazamiento (freno de tambor) ver tabla página 10

Los valores dados se aplican después de 100 horas de rodaje

2) Operación continua

3) Los valores máximos pueden producirse durante una duración máxima de un solo segundo dentro de un minuto de funcionamiento

4) Recomendamos Pmín = 15 bar en la línea de retorno

5) Fluidos ecológicos HETG, HEPG, HEES según RE 90 221

6) Cuando opere motores en serie, consulte con nuestra oficina técnica

7)⚠ Advertencia: Al poner en marcha el motor (mín. 20 horas), ten en cuenta que el motor no debe funcionar sin carga a una velocidad superior al 50 % de la velocidad máxima %.

8) Para el extremo de eje simple "L60", la presión diferencial máxima admisible Δp = 250 bar

Datos técnicos (valores medios, medidos a ν = 46 mm2/s y θ = 45℃)

Notas sobre datos técnicos

T = Par en Nm qV = Flujo de entrada en L/min qVL = Flujo de drenaje de la caja en L/min
-Todos los pares de apriete se aplican a motores en rodaje (ver nota p. 4, nota a pie de página 7)
-Para el modo de "medio desplazamiento", multiplique el par y la qV-valores en 0.5.
-Los valores de par a medio desplazamiento no se aplican a ambos sentidos de giro, sino únicamente al sentido de giro preferente marcado (véanse las páginas 7 a 9)
Tamaño 780 1250
Velocidad n en rpm 0 25 50 100 150 0 25 50 100 150
Diferencial de presión Δp en bar 100 T Nm 806 994 1049 1029 911 1094 1818 1726 1517 1309
qV L/min 0,3 19,8 39,47 79,00 118,2 1,00 32,09 63,73 126,69 189,30
qVL L/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76 0,90
200 T Nm 1736 2232 2282 2232 2158 2586 3669 3684 3497
qV L/min 0,60 20,10 39,80 79,50 118,8 2,86 33,03 64,63 127,82
qVL L/min 0,30 0,30 0,40 0,75 0,9 1,43 1,44 1,45 1,46
300 T Nm 2604 3348 3422 3348 4178 5550 5574
qV L/min 0,80 20,30 40,00 80,00 4,08 34,08 66,16
qVL L/min 0,40 0,40 0,50 1,00 2,04 2,10 2,16
400 T Nm 3472 4464 4563 5730 7432 7416
qV L/min 1,40 20,90 40,80 5,68 35,11 67,35
qVL L/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Nm 3906 5022 5134
qV L/min 1,6 21,10 41,00
qVL L/min 0,80 0,8 1,00
Tamaño 940 1340
Velocidad n en rpm 0 25 50 100 150 0 25 50 100
Diferencial de presión Δp en bar 100 T Nm 971 1198 1264 1240 1098 1182 1964 1865 1639
qV L/min 1,00 23,80 47,47 95,00 142,20 1,00 34,61 68,78 136,76
qVL L/min 0,15 0,15 0,24 0,50 0,60 0,50 0,56 0,63 0,76
200 T Nm 2091 2690 2750 2689 2793 3962 3979 3777
qV L/min 0,60 24,10 47,80 95,50 2,86 35,56 69,68 137,93
qVL L/min 0,30 0,30 0,40 0,75 1,43 1,44 1,45 1,46
300 T Nm 3137 4035 4124 4512 5994 6020
qV L/min 0,80 24,30 48,00 4,08 36,64 71,24
qVL L/min 0,40 0,40 0,50 2,04 2,10 2,16
400 T Nm 4183 5380 5500 6188 8027 8010
qV L/min 1,40 24,90 48,80 5,68 37,67 72,50
qVL L/min 0,70 0,70 0,90 2,84 2,92 3,00
450 T Nm 4706 6052 6187
qV L/min 1,60 25,10 49,00
qVL L/min 0,80 0,80 1,00
Tamaño 1120
Velocidad n en rpm 0 25 50 100 150
Diferencial de presión Δp en bar 100 T Nm 980 1629 1547 1360 1173
qV L/min 1,00 28,82 57,19 113,62 169,80
qVL L/min 0,50 0,56 0,63 0,76 0,90
200 T Nm 2317 3287 3301 3134
qV L/min 2,86 29,76 58,07 114,71
qVL L/min 1,43 1,44 1,45 146
300 T Nm 3743 4973 4994
qV L/min 4,08 30,76 59,49
qVL L/min 2,04 2,10 2,16
400 T Nm 5134 6660 6645
qV L/min 5,68 31,76 60,87
qVL L/min 2,84 2,92 3,00