شركة ونزهو برانس للمعدات الهيدروليكية المحدودة
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
- Variable displacement A10 motor
- Output speed depends on flow and displacement
- Torque depends on pressure difference and displacement
- SAE two-bolt mounting reference
PRANCE HYDRAULIC · PRODUCT SERIES
Axial piston; swashplate variable displacement · Confirm open or closed circuit conditions
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
Model

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Configuration review · Technical documentation · Product selection
تفاصيل المنتج
- Variable displacement A10 motor
- Output speed depends on flow and displacement
- Torque depends on pressure difference and displacement
- SAE two-bolt mounting reference
CATEGORIES: محرك مكبس, محرك مكبس متغير الإزاحة
A10VM Features & Application
Variable displacement A10 motor
Specify the displacement range or switching arrangement and verify performance at each required setting.
Output speed depends on flow and displacement
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
Torque depends on pressure difference and displacement
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
SAE two-bolt mounting reference
Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.
A10VM Specifications
| Series / model | A10VM |
|---|---|
| Product type | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| تصميم | Axial piston; swashplate variable displacement |
| Circuit / selection | Confirm open or closed circuit conditions |
| التحكم في السعة | Variable |
| Mounting reference | SAE two-bolt flange in the existing description |
A10VM Selection & Configuration
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
Define the required displacement range and its control behavior before selecting the motor. Check the highest commanded speed and the torque available at minimum displacement, then match the SAE flange, shaft, ports and drain arrangement to the installation.

Your Application.
The Right Configuration.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

A10VM Buying Guide
Use this sequence to prepare the A10VM configuration for review and quotation.
- Define starting and continuous torque, speed range and duty cycle.
- Specify available flow, work-port pressure difference and return pressure.
- Confirm the displacement setting and required behavior during starting and stopping.
- Check shaft, mounting pilot, flange, port orientation and external loads.
- Review case drainage, replenishment and any displacement control.
- Specify fluid conditions and any independent braking requirement.
- Approve the complete model, operating envelope, drawing and quantity.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

Project Inquiries
Learn more →Send your required model, quantity, application and project requirements to discuss your inquiry.
Product inquiries · Configuration review
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your A10VM Application
Send the full model code, operating duty, installation details and quantity.
Request a A10VM QuotationA10VM Questions Before Ordering
What type of product is the A10VM?
A10VM Variable Displacement Axial Piston Motor. Design: Axial piston; swashplate variable displacement. Confirm open or closed circuit conditions. Confirm the complete order code for the offered version.
Can a similar motor replace the A10VM?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
A10VM Technical Data & Documents
View A10VM catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
البيانات الفنية
Fluid
Prior to project design please see our data sheets RE 90220(mineral oil), RE 90221 (ecologically acceptable fluids) and RE90223(HF-fluids) for detailed information on fluids and application conditions. When operating on ecologically acceptable fluids, limitations to the technical data may be necessary. Please contact us and state the fluid used in clear text when ordering.Operating viscosity range
For optimum efficiency and service life we recommend an ope-rating viscosity (at operating temperature) in the range νاختيار = opt. operating viscosity 16…36 mm2/s referred to circuit temperature in closed circuits or tank temperature in open circuits. The following limits are valid for extreme operating conditions: Vالحد الأدنىcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s (closed circuit) Vالحد الأدنى=10 mm2/s (open circuit) briefly (t≤ 1 min) at max. permissible temperature of 115℃. Please note, that the max. fluid temperature of 115℃ may also not be exceeded in certain areas (for instance bearing area) The temperature in the bearing area is approx. 5 K higher than the average fluid temperature. νالحد الأقصىcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s briefly (t≤ 1 min) on cold start (tالحد الأدنى = -25℃, p≤30 bar, n≤1000 rpm). At temperatures between -25 ℃ and -40 ℃ special measures may be required for certain installation positions. Please consult us for further information For detailed information on operation at very low temperatures see RE 90300-03-B.Notes on the selection of the hydraulic fluid
In order to select the correct fluid, it is necessary to know the operating temperature in the tank (open circuit), circuit temperature (closed circuits), in relation to the ambient temperature. The fluid should be selected, so that within the operating temperature range, the viscosity lies within the optimum range(νاختيار), see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case. Example: at an ambient temperature of X ℃ the operating temperature in the tank is 60℃.In the optimum viscosity range(νاختيار; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; select VG 68. Important: The leakage fluid (case drain fluid) temperature is influenced by pressure and motor speed and is always higher than the tank temperature. However, at no point in the circuit may the temperature exceed 115 ℃. If it is not possible to comply with the above conditions because of extreme operating parameters or high ambient temperatures please consult usFiltration of fluid
The finer the filtration the better the achieved cleanliness of the fluid and the longer the life of the axial piston unit. To ensure a reliable functioning of the axial piston unit, a minimum cleanliness of 20/18/15 to ISO 4406 is necessary. At very high fluid temperatures (90℃ to max. 115℃) the minimum cleanliness has to be at least 19/17/14 to ISO 4406. If above cleanliness classes cannot be met please consult us.Operating pressure range
Pressure at port A or B (Pressure data to DIN 24312)| Nominal pressure pN | 280 bar 1) |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsالحد الأقصى | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| مع عقارب الساعة | عكس عقارب الساعة | ||||
| B to A | A to B | ||||
مخطط الاختيار
Table of values(theoretical values, without efficiency levels and tolerances; values rounded)
| حجم | 28 | 45 | 63 | 85 | |||
| إزاحة | Vجي ماكس | سم3 | 28 | 45 | 62 | 87 | |
| Vج مين | سم3 | 8 (VM)/10(VE) | 12 | 16 | 22 | ||
| سرعة1) | 4700 | 4000 | 3300 | 3100 | |||
| max. at Vجي ماكس | ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | الحد الأدنى-1 | |||||
| max. at Vج مين | n0 max zul | الحد الأدنى-1 | 5400 | 4600 | 3900 | 3560 | |
| Min.speed in cont. operation | n0 min | الحد الأدنى-1 | 250 | 250 | 250 | 250 | |
| تدفق المدخل | 131,6 | 180 | 205 | 270 | |||
| bei ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits و Vجي ماكس | qv0 الحد الأقصى | لتر/دقيقة | |||||
| Torque constant2) عند Vجي ماكس | TK | Nm/bar | 0,445 | 0,716 | 1,002 | 1,35 | |
| عزم الدوران | 125 | 200 | 276 | 387 | |||
| عند Vجي ماكس | PN= 280 bar | Tالحد الأقصى | لا شيء جديد | ||||
| Actual starting torque | 92 | 149 | 205 | 253 | |||
| at n=0 min-1 | PN = 280 bar | T | Nm ca. | ||||
| صلابة الدوران | Shaft R | c | نيوتن متر/راديان | 26000 | 41000 | 69400 | 152900 |
| Shaft W | c | نيوتن متر/راديان | 19800 | 34400 | 54000 | 117900 | |
| Mass moment of inertia (about output shaft) | J | كجم متر2 | 0,0017 | 0,0033 | 0,0056 | 0,012 | |
| Filling volume | V | L | 0,6 | 0,7 | 0,8 | 1,0 | |
| Weight approx. | m | kg | 14 | 18 | 26 | 34 | |
depending on motor speed
Calculating size
| تدفق | qv=(VgcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsv) | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Vg=Displacement per rev. in cm3 Δp=Differential pressure in bar n=speed in rpm ηv=Volumetric efficiency ηمم=Mechanical-hydraulic efficiency ηt=Total efficiency (ηt = ηv ∙ηممcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsK=Torque constant |
| عزم الدوران | T=(1,59∙Vg∙ Δp∙ηمم)/100 | [نيوتن متر] | |
| أو | T=Tk∙ Δp∙ηمم | ||
| Output power | P=(2π∙T∙n)/60000=(qv∙Δp∙ηt)/600 | [ك.و] | |
| سرعة الخرج | n=(qv∙1000∙ηv)/Vg | [min-1] | |
Permissible radial and axial forces on drive shaft
| حجم | 28 | 45 | 63 | 85 | ||||
| Max. radial force | ![]() |
at X/2 | Fq الحد الأقصى | N | 1200 | 1500 | 1700 | 2000 |
| Max. axial force | ![]() |
Fفأس | N | 1000 | 1500 | 2000 | 3000 | |
Watch A10VM Product Video
Related Selection Resources
Request a A10VM Quotation
أخبرنا بالتكوين المطلوب، الكمية والتطبيق.
رمز الطلب للبرنامج القياسي
| A10V | M | / | 52 | W | – | V | C | ||||||||
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 |
وحدة كباس محوري
| 01 | Swash plate design, variable, nominal pressure 280 bar, maximum pressure 350 bar | A10V |
Operating Mode
| 02 | Motor, open and closed circuit | M |
المقاس (NG)
| 03 | الإزاحة Vجي ماكس بالسنتيمتر3 | 028 | 045 | 063 | 085 |
أجهزة التحكم
| 028 | 045 | 063 | 085 | ||||||
| 04 | Two point سيطرة |
Directly operated, external control supply, without pilot valve | ● | ● | ● | ● | دي جي | ||
| Hydraulically operated | Stroking time | without | ● | ● | ● | ○ | HZ | ||
| Electricaly with solenoid valve | orifice | with | ● | ● | ● | ○ | HZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | ● | إي زي 1 | ||
| control voltage 12V | orifice | with | ● | ● | ● | ● | EZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | ○ | EZ2 | ||
| control voltage 24V | orifice | with | ● | ● | ● | ○ | EZ7 | ||
مسلسل
| 05 | Series 5, Index 2 | 52 |
اتجاه الدوران
| 06 | Viewed on shaft end Bi-directional | W |
Minimum displacement
| 028 | 045 | 063 | 085 | ||||
| 07 | Vج مين (in cm3) steplessly adjustable | from/to | 8/28 | 12/25 | 16/38 | 22/50 | 1 |
| Adjustment state in clear text | from/to | – | 26/45 | 40/62 | 48/85 | 2 | |
أختام
| 08 | FKM (flour-rubber) | V |
عمود الدوران
| 028 | 045 | 063 | 085 | |||
| 09 | Splined shaft, ANSI B92.1 a-1976, for higher drive torque | ● | ● | ● | ● | R |
| Splined shaft, ANSI B92.1 a-1976, for reduced drive torque | – | ● | ● | ● | W | |
شفة التركيب
| 10 | SAE J744 2-bolt | C |
Ports for service lines
| 11 | SAE flanges, at side-same side, metric fixing screws | ● | ● | ● | ● | 10N00 | |||||
| SAE flanges at rear, metric fixing screws | ○ | ● | ○ | ○ | 11N00 | ||||||
| Threaded ports on side, same side, metric thread | ● | ● | ● | ○ | 16N00 | ||||||
Valves
| 12 | Without valves | ● | ● | ● | ● | 0 | |||||
| Integrated flushing valve, only with side ports (10N00 and 16N00) | ● | ● | ● | ● | 7 | ||||||
Speed pickup
| 13 | Without speed pickup | ● | ● | ● | ● | – | ||||
| Prepared for inductive type of speed pickup ID R | ● | ● | ● | ○ | D | |||||
موصل للملفات اللولبية
| 14 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ▲ | ▲ | ▲ | ▲ | H | |||||
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ● | ● | ● | ● | P | ||||||
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
| A10V | E | / | 52 | W | – | V | F | ||||||||
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 |
وحدة كباس محوري
| 01 | Swash plate design, variable, nominal pressure 280 bar, maximum pressure 350 bar | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||||
نمط التشغيل
| 02 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | E | |||
المقاس (NG)
| 03 | الإزاحة Vجي ماكس بالسنتيمتر3 | 028 | 045 | 063 |
أجهزة التحكم
| 028 | 045 | 063 | ||||||
| 04 | Two point سيطرة |
Directly operated, external control supply, without pilot valve | ● | ● | ○ | دي جي | ||
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Stroking time | without | ● | ● | ● | HZ | ||
| orifice | with | ● | ● | ● | HZ6 | |||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | إي زي 1 | ||
| control voltage 12V | orifice | with | ● | ● | ● | EZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | EZ2 | ||
| control voltage 24V | orifice | with | ● | ● | ● | EZ7 | ||
مسلسل
| 05 | Series 5, Index 2 | 52 |
اتجاه الدوران
| 06 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | W | ||||
Minimum displacement
| 028 | 045 | 063 | ||||
| 07 | Vج مين (in cm3cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | from/to | 10/28 | 12/25 | 16/38 | 1 |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | from/to | – | 26/45 | 40/62 | 2 | |
أختام
| 08 | FKM (flour-rubber) | V |
عمود الدوران
| 028 | 045 | 063 | |||||||
| 09 | Splined shaft, ANSI B92.1 a-1976, for higher drive torque | ● | ● | ● | R | ||||
| Splined shaft, ANSI B92.1 a-1976, for reduced drive torque | – | ● | ● | W | |||||
شفة التركيب
| 10 | Special 2-bolt | F |
Ports for service line
| 11 | SAE flanges at side-same side, metric fixing screws | ● | ● | ● | 10N00 | ||||
| SAE flanges at rear, metric fixing screws | ○ | ● | ○ | 11N00 | |||||
| Threaded ports on side, same side, metric thread | ● | ● | ● | 16N00 | |||||
Valves
| 12 | Without valves | ● | ● | ● | 0 | |||||
| Integrated flushing valve, only with side ports (10N00 and 16N00) | ● | ● | ● | 7 | ||||||
Speed pickup
| 13 | Without speed pickup | ● | ● | ● | – | ||||
| Prepared for inductive type of speed pickup ID R | ○ | ● | ○ | D | |||||
موصل للملفات اللولبية
| 14 | HIRSCHMANN - connector—without suppressor diod | ▲ | ▲ | ▲ | H | |||||
| DEUTSCH - connector, molded, 2-pin—without suppressor diod | ● | ● | ● | P | ||||||
•=available ○=in preparation — =not available ▲=not for new projects
البيانات الفنية
Fluid
Prior to project design please see our data sheets RE 90220(mineral oil), RE 90221 (ecologically acceptable fluids) and RE90223(HF-fluids) for detailed information on fluids and application conditions.
When operating on ecologically acceptable fluids, limitations to the technical data may be necessary.
Please contact us and state the fluid used in clear text when ordering.
Operating viscosity range
For optimum efficiency and service life we recommend an ope-rating viscosity (at operating temperature) in the range
νاختيار = opt. operating viscosity 16...36 mm2/s
referred to circuit temperature in closed circuits or tank temperature in open circuits.
The following limits are valid for extreme operating conditions:
Vالحد الأدنىcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Vالحد الأدنى=10 mm2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
briefly (t≤ 1 min) at max. permissible temperature of 115℃.
Please note, that the max. fluid temperature of 115℃ may also not be exceeded in certain areas (for instance bearing area)
The temperature in the bearing area is approx. 5 K higher than the average fluid temperature.
νالحد الأقصىcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s
briefly (t≤ 1 min)
on cold start (tالحد الأدنى = -25℃, p≤30 bar, n≤1000 rpm).
At temperatures between -25 ℃ and -40 ℃ special measures may be required for certain installation positions. Please consult us for further information
For detailed information on operation at very low temperatures see RE 90300-03-B.
Notes on the selection of the hydraulic fluid
In order to select the correct fluid, it is necessary to know the operating temperature in the tank (open circuit), circuit temperature (closed circuits), in relation to the ambient temperature.
The fluid should be selected, so that within the operating temperature range, the viscosity lies within the optimum range(νاختيار),see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case.
Example: at an ambient temperature of X ℃ the operating temperature in the tank is 60℃.In the optimum viscosity range(νاختيار; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; select VG 68.
Important: The leakage fluid (case drain fluid) temperature is influenced by pressure and motor speed and is always higher than the tank temperature. However, at no point in the circuit may the temperature exceed 115 ℃.
If it is not possible to comply with the above conditions because of extreme operating parameters or high ambient temperatures please consult us
Filtration of fluid
The finer the filtration the better the achieved cleanliness of the fluid and the longer the life of the axial piston unit.
To ensure a reliable functioning of the axial piston unit, a minimum cleanliness of
20/18/15 to ISO 4406 is necessary.
At very high fluid temperatures (90℃ to max. 115℃) the minimum cleanliness has to be at least
19/17/14 to ISO 4406.
If above cleanliness classes cannot be met please consult us.
Operating pressure range
Pressure at port A or B
(Pressure data to DIN 24312)
| Nominal pressure pN | 280 bar 1) |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsالحد الأقصى | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. | |
ضغط تصريف العلبة
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabs cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
اتجاه الدوران
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| مع عقارب الساعة | عكس عقارب الساعة | ||||
| B to A | A to B | ||||
Adjustment of displacement
The minimum displacement is steplessly adjustable within the range of the screw lengths
1 or 2 (see ordering code).
Please state minimum displacement in clear text when ordering.
مخطط الاختيار

Table of values(theoretical values, without efficiency levels and tolerances; values rounded)
| حجم | 28 | 45 | 63 | 85 | |||
| إزاحة | Vجي ماكس | سم3 | 28 | 45 | 62 | 87 | |
| Vج مين | سم3 | 8 (VM)/10(VE) | 12 | 16 | 22 | ||
| سرعة1) | 4700 | 4000 | 3300 | 3100 | |||
| max. at Vجي ماكس | ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | الحد الأدنى-1 | |||||
| max. at Vج مين | n0 max zul | الحد الأدنى-1 | 5400 | 4600 | 3900 | 3560 | |
| Min.speed in cont. operation | n0 min | الحد الأدنى-1 | 250 | 250 | 250 | 250 | |
| تدفق المدخل | 131,6 | 180 | 205 | 270 | |||
| bei ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits و Vجي ماكس | qv0 الحد الأقصى | لتر/دقيقة | |||||
| Torque constant2) عند Vجي ماكس | TK | Nm/bar | 0,445 | 0,716 | 1,002 | 1,35 | |
| عزم الدوران | 125 | 200 | 276 | 387 | |||
| عند Vجي ماكس | PN= 280 bar | Tالحد الأقصى | لا شيء جديد | ||||
| Actual starting torque | 92 | 149 | 205 | 253 | |||
| at n=0 min-1 | PN = 280 bar | T | Nm ca. | ||||
| صلابة الدوران | Shaft R | c | نيوتن متر/راديان | 26000 | 41000 | 69400 | 152900 |
| Shaft W | c | نيوتن متر/راديان | 19800 | 34400 | 54000 | 117900 | |
| Mass moment of inertia (about output shaft) | J | كجم متر2 | 0,0017 | 0,0033 | 0,0056 | 0,012 | |
| Filling volume | V | L | 0,6 | 0,7 | 0,8 | 1,0 | |
| Weight approx. | m | kg | 14 | 18 | 26 | 34 | |
1) At maximal speed in closed circuit operation make sure that motor outlet pressure is at least≥18 bar.
2) In open circuit Δp 280bar at Pboostpress. 2bar
In closed circuit Δp 260bar at Pboostpress. 20bar
Minimum required outlet pressure (low pressure) at port A (B)
depending on motor speed

Calculating size
| تدفق | qv=(VgcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsv) | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Vg=Displacement per rev. in cm3 Δp=Differential pressure in bar n=speed in rpm ηv=الكفاءة الحجمية ηممcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits ηt=Total efficiency (ηt = ηv ∙ηمم) TK=Torque constant |
| عزم الدوران | T=(1,59∙Vg∙ Δp∙ηمم)/100 | [نيوتن متر] | |
| أو | T=Tk∙ Δp∙ηمم | ||
| Output power | P=(2π∙T∙n)/60000=(qv∙Δp∙ηt)/600 | [ك.و] | |
| سرعة الخرج | n=(qv∙1000∙ηv)/Vg | [min-1] | |
Permissible radial and axial forces on drive shaft
| حجم | 28 | 45 | 63 | 85 | ||||
| Max. radial force | ![]() |
at X/2 | Fq الحد الأقصى | N | 1200 | 1500 | 1700 | 2000 |
| Max. axial force | ![]() |
Fفأس | N | 1000 | 1500 | 2000 | 3000 | |









