Wenzhou Prance Hydraulic Equipment Co., Ltd
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
- Variable displacement A10 motor
- Output speed depends on flow and displacement
- Torque depends on pressure difference and displacement
- SAE two-bolt mounting reference
PRANCE HYDRAULIC · PRODUCT SERIES
Axial piston; swashplate variable displacement · Confirm open or closed circuit conditions
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
Modèle

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Étude de configuration · Documentation technique · Sélection de produits
Détails du produit
- Variable displacement A10 motor
- Output speed depends on flow and displacement
- Torque depends on pressure difference and displacement
- SAE two-bolt mounting reference
CATÉGORIES : Moteur à pistons, Moteur à pistons à cylindrée variable
A10VM Features & Application
Variable displacement A10 motor
Specify the displacement range or switching arrangement and verify performance at each required setting.
Output speed depends on flow and displacement
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
Torque depends on pressure difference and displacement
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
SAE two-bolt mounting reference
Check pilot diameter, bolt pattern, shaft engagement or port pattern against the approved installation drawing.
A10VM Specifications
| Series / model | A10VM |
|---|---|
| Product type | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Conception | Axial piston; swashplate variable displacement |
| Circuit / selection | Confirm open or closed circuit conditions |
| Contrôle du déplacement | Variable |
| Mounting reference | SAE two-bolt flange in the existing description |
A10VM Selection & Configuration
The A10VM variable displacement motor allows the torque-speed relationship to be changed through displacement. At the same flow, reducing displacement increases theoretical speed; at the same pressure difference it also reduces theoretical torque.
Define the required displacement range and its control behavior before selecting the motor. Check the highest commanded speed and the torque available at minimum displacement, then match the SAE flange, shaft, ports and drain arrangement to the installation.

Your Application.
The Right Configuration.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

A10VM Buying Guide
Use this sequence to prepare the A10VM configuration for review and quotation.
- Define starting and continuous torque, speed range and duty cycle.
- Specify available flow, work-port pressure difference and return pressure.
- Confirm the displacement setting and required behavior during starting and stopping.
- Check shaft, mounting pilot, flange, port orientation and external loads.
- Review case drainage, replenishment and any displacement control.
- Specify fluid conditions and any independent braking requirement.
- Approve the complete model, operating envelope, drawing and quantity.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Learn more →cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your A10VM Application
Send the full model code, operating duty, installation details and quantity.
Request a A10VM QuotationA10VM Questions Before Ordering
What type of product is the A10VM?
A10VM Variable Displacement Axial Piston Motor. Design: Axial piston; swashplate variable displacement. Confirm open or closed circuit conditions. Confirm the complete order code for the offered version.
Can a similar motor replace the A10VM?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
A10VM Technical Data & Documents
View A10VM catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Données techniques
Fluid
Prior to project design please see our data sheets RE 90220(mineral oil), RE 90221 (ecologically acceptable fluids) and RE90223(HF-fluids) for detailed information on fluids and application conditions. When operating on ecologically acceptable fluids, limitations to the technical data may be necessary. Please contact us and state the fluid used in clear text when ordering.Operating viscosity range
For optimum efficiency and service life we recommend an ope-rating viscosity (at operating temperature) in the range νopt = opt. operating viscosity 16…36 mm2/s referred to circuit temperature in closed circuits or tank temperature in open circuits. The following limits are valid for extreme operating conditions: VmincURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s (closed circuit) Vmin=10 mm2/s (open circuit) briefly (t≤ 1 min) at max. permissible temperature of 115℃. Please note, that the max. fluid temperature of 115℃ may also not be exceeded in certain areas (for instance bearing area) The temperature in the bearing area is approx. 5 K higher than the average fluid temperature. νmaxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s briefly (t≤ 1 min) on cold start (tmin = -25℃, p≤30 bar, n≤1000 rpm). At temperatures between -25 ℃ and -40 ℃ special measures may be required for certain installation positions. Please consult us for further information For detailed information on operation at very low temperatures see RE 90300-03-B.Notes on the selection of the hydraulic fluid
In order to select the correct fluid, it is necessary to know the operating temperature in the tank (open circuit), circuit temperature (closed circuits), in relation to the ambient temperature. The fluid should be selected, so that within the operating temperature range, the viscosity lies within the optimum range(νopt), see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case. Example: at an ambient temperature of X ℃ the operating temperature in the tank is 60℃.In the optimum viscosity range(νopt; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; select VG 68. Important: The leakage fluid (case drain fluid) temperature is influenced by pressure and motor speed and is always higher than the tank temperature. However, at no point in the circuit may the temperature exceed 115 ℃. If it is not possible to comply with the above conditions because of extreme operating parameters or high ambient temperatures please consult usFiltration of fluid
The finer the filtration the better the achieved cleanliness of the fluid and the longer the life of the axial piston unit. To ensure a reliable functioning of the axial piston unit, a minimum cleanliness of 20/18/15 to ISO 4406 is necessary. At very high fluid temperatures (90℃ to max. 115℃) the minimum cleanliness has to be at least 19/17/14 to ISO 4406. If above cleanliness classes cannot be met please consult us.Operating pressure range
Pressure at port A or B (Pressure data to DIN 24312)| Nominal pressure pN | 280 bar 1) |
| Maximum pressure Pmax | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| dans le sens des aiguilles d'une montre | dans le sens inverse des aiguilles d'une montre | ||||
| B to A | A to B | ||||
Diagramme de sélection
Tableau des valeurs(theoretical values, without efficiency levels and tolerances; values rounded)
| Taille | 28 | 45 | 63 | 85 | |||
| Déplacement | VGiga | cm3 | 28 | 45 | 62 | 87 | |
| Vsol mineur | cm3 | 8 (VM)/10(VE) | 12 | 16 | 22 | ||
| Vitesse1) | 4700 | 4000 | 3300 | 3100 | |||
| max. at VGiga | n0 max | min-1 | |||||
| max. at Vsol mineur | n0 max zul | min-1 | 5400 | 4600 | 3900 | 3560 | |
| Min.speed in cont. operation | n0 min | min-1 | 250 | 250 | 250 | 250 | |
| Débit d'entrée | 131,6 | 180 | 205 | 270 | |||
| bei n0 max et VGiga | qv0 max | L/min | |||||
| Torque constant2) à VGiga | TK | Nm/bar | 0,445 | 0,716 | 1,002 | 1,35 | |
| Couple | 125 | 200 | 276 | 387 | |||
| à VGiga | PN= 280 bar | Tmax | Rien | ||||
| Actual starting torque | 92 | 149 | 205 | 253 | |||
| at n=0 min-1 | PN = 280 bar | T | Nm ca. | ||||
| Rigidité rotative | Shaft R | c | Nm/rad | 26000 | 41000 | 69400 | 152900 |
| Shaft W | c | Nm/rad | 19800 | 34400 | 54000 | 117900 | |
| Mass moment of inertia (about output shaft) | J | kgm2 | 0,0017 | 0,0033 | 0,0056 | 0,012 | |
| Filling volume | V | L | 0,6 | 0,7 | 0,8 | 1,0 | |
| Poids approx. | m | kg | 14 | 18 | 26 | 34 | |
depending on motor speed
Calculating size
| Flux | qv=(VgcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsv) | [L/min] | Vg=Displacement per rev. in cm3 Δp=Differential pressure in bar n=speed in rpm ηv=Volumetric efficiency ηhm=Mechanical-hydraulic efficiency ηt=Total efficiency (ηt = ηv ∙ηhmcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsK=Torque constant |
| Couple | T=(1,59∙Vg∙ Δp∙ηhm)/100 | [Nm] | |
| ou | T=Tk∙ Δp∙ηhm | ||
| Output power | P=(2π∙T∙n)/60000=(qv∙Δp∙ηt)/600 | [kW] | |
| Vitesse de sortie | n=(qv∙1000∙ηv)/Vg | [min-1] | |
Permissible radial and axial forces on drive shaft
| Taille | 28 | 45 | 63 | 85 | ||||
| Max. radial force | ![]() |
at X/2 | Fq max | N | 1200 | 1500 | 1700 | 2000 |
| Max. axial force | ![]() |
Fhache | N | 1000 | 1500 | 2000 | 3000 | |
Watch A10VM Product Video
Related Selection Resources
Request a A10VM Quotation
Tell us your required configuration, quantity and application.
Ordering code for standard program
| A10V | M | / | 52 | W | – | V | C | ||||||||
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 |
Unité à pistons axiaux
| 01 | Swash plate design, variable, nominal pressure 280 bar, maximum pressure 350 bar | A10V |
Operating Mode
| 02 | Motor, open and closed circuit | M |
Taille (NG)
| 03 | Displacement VGiga en cm3 | 028 | 045 | 063 | 085 |
Dispositifs de contrôle
| 028 | 045 | 063 | 085 | ||||||
| 04 | Two point contrôle |
Directly operated, external control supply, without pilot valve | ● | ● | ● | ● | DG | ||
| Hydraulically operated | Stroking time | without | ● | ● | ● | ○ | HZ | ||
| Electricaly with solenoid valve | orifice | with | ● | ● | ● | ○ | HZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | ● | EZ1 | ||
| control voltage 12V | orifice | with | ● | ● | ● | ● | EZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | ○ | EZ2 | ||
| control voltage 24V | orifice | with | ● | ● | ● | ○ | EZ7 | ||
Séries
| 05 | Series 5, Index 2 | 52 |
Sens de rotation
| 06 | Viewed on shaft end Bi-directional | W |
Minimum displacement
| 028 | 045 | 063 | 085 | ||||
| 07 | Vsol mineur (in cm3) steplessly adjustable | from/to | 8/28 | 12/25 | 16/38 | 22/50 | 1 |
| Adjustment state in clear text | from/to | – | 26/45 | 40/62 | 48/85 | 2 | |
Joints d'étanchéité
| 08 | FKM (flour-rubber) | V |
Arbre de transmission
| 028 | 045 | 063 | 085 | |||
| 09 | Splined shaft, ANSI B92.1 a-1976, for higher drive torque | ● | ● | ● | ● | R |
| Splined shaft, ANSI B92.1 a-1976, for reduced drive torque | – | ● | ● | ● | W | |
Bride de fixation
| 10 | SAE J744 2-bolt | C |
Ports pour lignes de service
| 11 | SAE flanges, at side-same side, metric fixing screws | ● | ● | ● | ● | 10N00 | |||||
| SAE flanges at rear, metric fixing screws | ○ | ● | ○ | ○ | 11N00 | ||||||
| Threaded ports on side, same side, metric thread | ● | ● | ● | ○ | 16N00 | ||||||
Vannes
| 12 | Without valves | ● | ● | ● | ● | 0 | |||||
| Integrated flushing valve, only with side ports (10N00 and 16N00) | ● | ● | ● | ● | 7 | ||||||
Speed pickup
| 13 | Without speed pickup | ● | ● | ● | ● | – | ||||
| Prepared for inductive type of speed pickup ID R | ● | ● | ● | ○ | D | |||||
Connecteur pour solénoïdes
| 14 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ▲ | ▲ | ▲ | ▲ | H | |||||
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ● | ● | ● | ● | P | ||||||
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
| A10V | E | / | 52 | W | – | V | F | ||||||||
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 |
Unité à pistons axiaux
| 01 | Swash plate design, variable, nominal pressure 280 bar, maximum pressure 350 bar | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||||
Mode de fonctionnement
| 02 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | E | |||
Taille (NG)
| 03 | Displacement VGiga en cm3 | 028 | 045 | 063 |
Dispositifs de contrôle
| 028 | 045 | 063 | ||||||
| 04 | Two point contrôle |
Directly operated, external control supply, without pilot valve | ● | ● | ○ | DG | ||
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Stroking time | without | ● | ● | ● | HZ | ||
| orifice | with | ● | ● | ● | HZ6 | |||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | EZ1 | ||
| control voltage 12V | orifice | with | ● | ● | ● | EZ6 | ||
| Electricaly with solenoid valve | Stroking time | without | ● | ● | ● | EZ2 | ||
| control voltage 24V | orifice | with | ● | ● | ● | EZ7 | ||
Séries
| 05 | Series 5, Index 2 | 52 |
Sens de rotation
| 06 | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | W | ||||
Minimum displacement
| 028 | 045 | 063 | ||||
| 07 | Vsol mineur (in cm3cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | from/to | 10/28 | 12/25 | 16/38 | 1 |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | from/to | – | 26/45 | 40/62 | 2 | |
Joints d'étanchéité
| 08 | FKM (flour-rubber) | V |
Arbre de transmission
| 028 | 045 | 063 | |||||||
| 09 | Splined shaft, ANSI B92.1 a-1976, for higher drive torque | ● | ● | ● | R | ||||
| Splined shaft, ANSI B92.1 a-1976, for reduced drive torque | – | ● | ● | W | |||||
Bride de fixation
| 10 | Special 2-bolt | F |
Ports for service line
| 11 | SAE flanges at side-same side, metric fixing screws | ● | ● | ● | 10N00 | ||||
| SAE flanges at rear, metric fixing screws | ○ | ● | ○ | 11N00 | |||||
| Threaded ports on side, same side, metric thread | ● | ● | ● | 16N00 | |||||
Vannes
| 12 | Without valves | ● | ● | ● | 0 | |||||
| Integrated flushing valve, only with side ports (10N00 and 16N00) | ● | ● | ● | 7 | ||||||
Speed pickup
| 13 | Without speed pickup | ● | ● | ● | – | ||||
| Prepared for inductive type of speed pickup ID R | ○ | ● | ○ | D | |||||
Connecteur pour solénoïdes
| 14 | HIRSCHMANN - connector—without suppressor diod | ▲ | ▲ | ▲ | H | |||||
| DEUTSCH - connector, molded, 2-pin—without suppressor diod | ● | ● | ● | P | ||||||
•=available ○=in preparation — =not available ▲=not for new projects
Données techniques
Fluid
Prior to project design please see our data sheets RE 90220(mineral oil), RE 90221 (ecologically acceptable fluids) and RE90223(HF-fluids) for detailed information on fluids and application conditions.
When operating on ecologically acceptable fluids, limitations to the technical data may be necessary.
Please contact us and state the fluid used in clear text when ordering.
Operating viscosity range
For optimum efficiency and service life we recommend an ope-rating viscosity (at operating temperature) in the range
νopt = opt. operating viscosity 16...36 mm2/s
referred to circuit temperature in closed circuits or tank temperature in open circuits.
The following limits are valid for extreme operating conditions:
VmincURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Vmin=10 mm2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
briefly (t≤ 1 min) at max. permissible temperature of 115℃.
Please note, that the max. fluid temperature of 115℃ may also not be exceeded in certain areas (for instance bearing area)
The temperature in the bearing area is approx. 5 K higher than the average fluid temperature.
νmaxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2/s
briefly (t≤ 1 min)
on cold start (tmin = -25℃, p≤30 bar, n≤1000 rpm).
At temperatures between -25 ℃ and -40 ℃ special measures may be required for certain installation positions. Please consult us for further information
For detailed information on operation at very low temperatures see RE 90300-03-B.
Notes on the selection of the hydraulic fluid
In order to select the correct fluid, it is necessary to know the operating temperature in the tank (open circuit), circuit temperature (closed circuits), in relation to the ambient temperature.
The fluid should be selected, so that within the operating temperature range, the viscosity lies within the optimum range(νopt),see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case.
Example: at an ambient temperature of X ℃ the operating temperature in the tank is 60℃.In the optimum viscosity range(νopt; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; select VG 68.
Important: The leakage fluid (case drain fluid) temperature is influenced by pressure and motor speed and is always higher than the tank temperature. However, at no point in the circuit may the temperature exceed 115 ℃.
If it is not possible to comply with the above conditions because of extreme operating parameters or high ambient temperatures please consult us
Filtration of fluid
The finer the filtration the better the achieved cleanliness of the fluid and the longer the life of the axial piston unit.
To ensure a reliable functioning of the axial piston unit, a minimum cleanliness of
20/18/15 to ISO 4406 is necessary.
At very high fluid temperatures (90℃ to max. 115℃) the minimum cleanliness has to be at least
19/17/14 to ISO 4406.
If above cleanliness classes cannot be met please consult us.
Operating pressure range
Pressure at port A or B
(Pressure data to DIN 24312)
| Nominal pressure pN | 280 bar 1) |
| Maximum pressure Pmax | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. | |
Pression de drainage du carter
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Pabdos cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
Sens de rotation
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| dans le sens des aiguilles d'une montre | dans le sens inverse des aiguilles d'une montre | ||||
| B to A | A to B | ||||
Adjustment of displacement
The minimum displacement is steplessly adjustable within the range of the screw lengths
1 or 2 (see ordering code).
Please state minimum displacement in clear text when ordering.
Diagramme de sélection

Tableau des valeurs(theoretical values, without efficiency levels and tolerances; values rounded)
| Taille | 28 | 45 | 63 | 85 | |||
| Déplacement | VGiga | cm3 | 28 | 45 | 62 | 87 | |
| Vsol mineur | cm3 | 8 (VM)/10(VE) | 12 | 16 | 22 | ||
| Vitesse1) | 4700 | 4000 | 3300 | 3100 | |||
| max. at VGiga | n0 max | min-1 | |||||
| max. at Vsol mineur | n0 max zul | min-1 | 5400 | 4600 | 3900 | 3560 | |
| Min.speed in cont. operation | n0 min | min-1 | 250 | 250 | 250 | 250 | |
| Débit d'entrée | 131,6 | 180 | 205 | 270 | |||
| bei n0 max et VGiga | qv0 max | L/min | |||||
| Torque constant2) à VGiga | TK | Nm/bar | 0,445 | 0,716 | 1,002 | 1,35 | |
| Couple | 125 | 200 | 276 | 387 | |||
| à VGiga | PN= 280 bar | Tmax | Rien | ||||
| Actual starting torque | 92 | 149 | 205 | 253 | |||
| at n=0 min-1 | PN = 280 bar | T | Nm ca. | ||||
| Rigidité rotative | Shaft R | c | Nm/rad | 26000 | 41000 | 69400 | 152900 |
| Shaft W | c | Nm/rad | 19800 | 34400 | 54000 | 117900 | |
| Mass moment of inertia (about output shaft) | J | kgm2 | 0,0017 | 0,0033 | 0,0056 | 0,012 | |
| Filling volume | V | L | 0,6 | 0,7 | 0,8 | 1,0 | |
| Poids approx. | m | kg | 14 | 18 | 26 | 34 | |
1) At maximal speed in closed circuit operation make sure that motor outlet pressure is at least≥18 bar.
2) In open circuit Δp 280bar at Pboostpress. 2bar
In closed circuit Δp 260bar at Pboostpress. 20bar
Minimum required outlet pressure (low pressure) at port A (B)
depending on motor speed

Calculating size
| Flux | qv=(VgcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsv) | [L/min] | Vg=Displacement per rev. in cm3 Δp=Differential pressure in bar n=speed in rpm ηv=Rendement volumétrique ηhm=Efficacité mécanique-hydraulique ηt=Total efficiency (ηt = ηv ∙ηhm) TK=Torque constant |
| Couple | T=(1,59∙Vg∙ Δp∙ηhm)/100 | [Nm] | |
| ou | T=Tk∙ Δp∙ηhm | ||
| Output power | P=(2π∙T∙n)/60000=(qv∙Δp∙ηt)/600 | [kW] | |
| Vitesse de sortie | n=(qv∙1000∙ηv)/Vg | [min-1] | |
Permissible radial and axial forces on drive shaft
| Taille | 28 | 45 | 63 | 85 | ||||
| Max. radial force | ![]() |
at X/2 | Fq max | N | 1200 | 1500 | 1700 | 2000 |
| Max. axial force | ![]() |
Fhache | N | 1000 | 1500 | 2000 | 3000 | |









