A10VSO Series 52 Variable Piston Pump

The A10VSO Series 52 page covers an open-circuit variable displacement pump. Keep the Series 52 identity in the request and compare the exact control, shaft and ports; a Series 53 photograph or a similar displacement does not establish a replacement.

  • Series 52 model reference
  • Open-circuit swashplate pump
  • Variable displacement flow
  • Control and interface selection by full code
HOME › Hydraulikpumpen › A10VSO Series 52

PRANCE HYDRAULIC · PRODUCT SERIES

A10VSO Series 52 Variable Piston Pump

Axial piston; variable swashplate · Open circuit

The A10VSO Series 52 page covers an open-circuit variable displacement pump. Keep the Series 52 identity in the request and compare the exact control, shaft and ports; a Series 53 photograph or a similar displacement does not establish a replacement.

Model

✓A10VSO Series 52 original product photograph
A10VSO Series 52Axial piston; variable swashplate
Request a QuotationTechnische Daten & Datenblatt anzeigen

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Configuration review · Technical documentation · Product selection

Produktdetails

  • Series 52 model reference
  • Open-circuit swashplate pump
  • Variable displacement flow
  • Control and interface selection by full code

CATEGORIES: Kolbenpumpe, Verstellpumpe

A10VSO Series 52 Features & Application

Series 52 model reference

Include the series and all order-code suffixes in the enquiry. A common nominal size does not establish compatibility.

Open-circuit swashplate pump

Review normal running, startup and reversal where applicable. The pressure and flow requirements can differ between operating states.

Variable displacement flow

Specify the displacement range or switching arrangement and verify performance at each required setting.

Control and interface selection by full code

Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.

A10VSO Series 52 Specifications

Series / modelA10VSO Series 52
Product typeA10VSO Series 52 Variable Piston Pump
DesignAxial piston; variable swashplate
Circuit / selectionOpen circuit
Serie52
Published family nominal-size table10, 18, 28, 45, 60, 63, 72, 85 and 100; availability is configuration-specific

A10VSO Series 52 Selection & Configuration

The A10VSO Series 52 page covers an open-circuit variable displacement pump. Keep the Series 52 identity in the request and compare the exact control, shaft and ports; a Series 53 photograph or a similar displacement does not establish a replacement.

Select the displacement from the required flow at the working speed and review the full pressure-duty cycle. Confirm which sizes and controls are offered for the exact A10VSO Series 52 code, rather than treating a combined series table as an availability list.

A10VSO Series 52 original product view

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the A17FO Series 10 nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

A10VSO Series 52 Buying Guide

Use this sequence to prepare the A10VSO Series 52 configuration for review and quotation.

  1. Define required flow at the actual drive speed and continuous pressure.
  2. Identify peak pressure, duration and the work cycle.
  3. Confirm the selected displacement control and any auxiliary-drive requirement.
  4. Match rotation viewed from the shaft end, shaft, flange and ports.
  5. Review inlet conditions, drain routing and the installation envelope.
  6. Confirm fluid, viscosity, temperature, filtration and seals.
  7. Approve the complete model, control, drawing, quantity and delivery terms.
A10VSO Series 52 original product photograph for installation review

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Project Inquiries

Learn more →

Send your required model, quantity, application and project requirements to discuss your inquiry.


Product inquiries · Configuration review

Configuration, Quantity & Delivery

Confirm the complete A17FO Series 10 code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your A10VSO Series 52 Application

Send the full model code, operating duty, installation details and quantity.

Request a A10VSO Series 52 Quotation

A10VSO Series 52 Questions Before Ordering

What type of product is the A10VSO Series 52?

A10VSO Series 52 Variable Piston Pump. Design: Axial piston; variable swashplate. Open circuit. Confirm the complete order code for the offered version.

Can a similar pump replace the A10VSO Series 52?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.

A10VSO Series 52 Technical Data & Documents

View A10VSO Series 52 catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Technische Daten

Größe NG 10 18 28 45 60 63 72 85 100
Geometrisches Fördervolumen pro Umdrehung Vg Max cm3 10.5 18 28 45 60 63 72 85 100
Rotational speed maximum1) bei VG-Max nnom U/min 3600 3300 3000 26004) 2700 2600 2600 2500 2300
bei Vg <Vg Max 2) nmax. Zul. U/min 4320 3960 3600 3120 3140 3140 3140 3000 2500
Fluss unter nnom und VG-Max qv l/min 37 59 84 117 162 163 187 212 230
unter nE = 1500 U/min qvE l/min 15 27 42 68 90 95 108 128 150
Macht Mit Nnom, VG-Max und Δp = 250 bar P kW 16 25 35 49 65 68 77 89 96
unter nE= 1500 U/min PE kW 7 11 18 28 37 39 45 53 62
Drehmoment bei VG-Max und Δp = 250 bar M Machs gut 42 71 111 179 238 250 286 338 398
bei VG-Max und Δp = 100 bar M Machs gut 17 29 45 72 95 100 114 135 159
Drehsteifigkeit Antriebswelle S c Nm/rad 9200 11000 22300 37500 65500 65500 65500 143000 143000
R c Nm/rad – 14800 26300 41000 69400 69400 69400 152900 152900
U c Nm/rad 6800 8000 16700 30000 49200 49200 49200 102900 102900
W c Nm/rad – – 19900 34400 54000 54000 54000 117900 117900
P c Nm/rad 10700 – – – – – – – –
Trägheitsmoment der Triebwerksgruppe JTW Kgm2 0.0006 0.0009 0.0017 0.003 0.0056 0.0056 0.0056 0.012 0.012
Maximale Winkelbeschleunigung3) α rad/s2 8000 6800 5500 4000 3300 3300 3300 2700 2700
Fallzahl V L 0.2 0.25 0.3 0.5 0.8 0.8 0.8 1 1
Weight without through drive (approx.) Weight with through drive (approx.) m kg 8 11.5 15 18 22 22 22 36 36
– 13 18 24 28 28 28 45 45

Bestimmung der Betriebskennlinien

Key Vg  Fördervolumen pro Umdrehung in [cm3] Δp  Differential pressure [bar] n   Rotational speed [rpm] ηv   Volumetric efficiency ηhm  Hydraulic-mechanical efficiency ηt   Gesamtwirkungsgrad (ηt= ηv*ηhm) 1) The values are applicable: – At an abs. pressure pABS = 1 bar at the suction port S – for the optimum viscosity range from Ventscheiden = 36 bis 16 mm2/s – with hydraulic fluid on the basis of mineral oils 2)Siehe Diagramm auf Seite 9 bei einer Geschwindigkeitserhöhung bis zu nmax adm. 3)Die Daten gelten für Werte zwischen der minimal erforderlichen und der maximal zulässigen Drehzahl. Sie gilt für externe Anregungen (z. B. Dieselmotor das 2- bis 8-fache der Drehfrequenz, Kardanwelle das doppelte der Drehfrequenz). Der Grenzwert gilt nur für eine einzelne Pumpe. Die Belastbarkeit der Verbindungsteile muss berücksichtigt werden.

Zulässige Radial- und Axialkräfte auf die Antriebswelle

Größe NG 10 18 28 45 60/63 72 85 100
Maximale Radialkraft bei a/2 A10VSO Series 52 technical reference from the existing product documentation FQ-max N 250 350 1200 1500 1700 1500 2000 2000
Maximale Axialkraft A10VSO Series 52 technical reference from the existing product documentation ±FAch, Max N 400 700 1000 1500 2000 1500 3000 3000

Zulässige Eingangs- und Durchtriebsdrehmomente

Größe 10 18 28 45 60/63 72 85 100
Maximales Eingangsdrehmoment an der Antriebswelle2)
S ME max Machs gut 126 124 198 319 630 630 1157 1157
∅ in 3/4 3/4 7/8 1 1 1/4 1 1/4 1 1/2 1 1/2
R ME max Machs gut – 160 250 400 650 650 1215 1215
∅ in – 3/4 7/8 1 1 1/4 1 1/4 1 1/2 1 1/2
U ME max Machs gut 60 59 105 188 306 306 628 628
∅ in 5/8 5/8 3/4 7/8 1 1 1 1/4 1 1/4
W ME max Machs gut – – 140 220 396 383 650 650
∅ in – – 3/4 7/8 1 1 1 1/4 1 1/4
P ME max Machs gut 90 – – – – – – –
∅ mm 18 – – – – – – –
Maximales Durchtriebsdrehmoment
S MD max Machs gut – 108 160 319 484 484 698 698
R MD max Machs gut – 120 176 365 484 484 698 –
U MD max Machs gut – 59 105 188 306 306 628 628
W MD max Machs gut – – 140 220 396 383 650 650

Drehmomentverteilung

  A10VSO Series 52 technical reference from the existing product documentation
Eingangsdrehmoment ME=M1+M2+M3
ME < ME max
Durchtriebsdrehmoment MD=M2+M3
MD < MD max
1)Effizienz nicht berücksichtigt 2) Für Gelenkwellen ohne Radialkraft
Watch A10VSO Series 52 Product Video
A10VSO Series 52 product video

Request a A10VSO Series 52 Quotation

Tell us your required configuration, quantity and application.

Kontaktformular-Demo
A10VSO Series 52 original product photograph

Typenreihe 52

01 02 03 04 05 06 07 08 09 10 11 12
A10V(S) ○ / 32 - v

Axialkolbeneinheit

10 28 45 60 85
01 Schrägscheibenbauweise, verstellbar, Nenndruck 250 bar, Maximaldruck 315 bar ● - - - - A10VS
- ● ● ● ● A10V

Betriebsart

02 Pumpe, offener Kreisklauf ○

Größe (NG)

03 Geometrisches Fördervolumen, siehe Wertetabelle auf Seite 10 10 28 45 60 85

Steuergerät

04 Druckregler hydraulisch ● ● ● ● ● DR
mit Durchflussregler hydraulisch X-T öffnen ● ● ● ● ● DFR
X-T eingesteckt mit Spülfunktion ● ● ● ● ● DFR1
ohne Spülfunktion ● ● ● ● ● DRSC
mit Abschaltvorrichtung hydraulisch fernbedient ● ● ● ● ● DRG
elektrisch Negativkontrolle U=12V ● ● ● ● ● ED71
U=24V ● ● ● ● ● ED72
elektrisch Positivkontrolle U=12V ● ● ● ● ● ER71
U=24V ● ● ● ● ● ER72
Differenzdruckregelung elektrische Steuerung (Minussteuerung) ● ● ● ● ○ EF..1)

Serie

10 28 45 60 85
05 Serie 5, Index 2 ● ● ● ● ● 52

Drehrichtung

06 Auf Antriebswelle betrachtet im Uhrzeigersinn R
gegen den Uhrzeigersinn L

 Dichtungsmaterial

07 FKM (Fluorelastomer) V

Antriebswelle

08 Kerbwelle

ISO 3019-1

Standardwelle ● ● ● ● ● S
ähnlich wie Welle "S", jedoch für höheres Eingangsdrehmoment - ● ● ● ● R
reduzierter Durchmesser, eingeschränkte Eignung für den Durchtrieb ● ● ● ● ● U
ähnlich wie Welle "U", jedoch für höheres Drehmoment; nur bedingt für die Montage mit Durchtrieb geeignet. - ● ● ● ● W
Passfederwelle DIN 6885 bedingt geeignet für Durchtrieb ● - - - - P

Montageflansch

09 ISO 3019-2 (ISO)  2-Loch ● - - - - A
ISO 3019-1 (SAE)  4-Loch ● ● ● ● ● C
 4-Loch - - - ● - D

Funktionierender Port

10 28 45 60 85
10 SAE-Flanschanschlüsse Befestigungsgewinde metrisch hintere Nicht als Durchfahrt geeignet - ● ● ● ● 11
diagonal gegenüber für Durchtrieb - ● ● ● ● 12
seitlich, Versatz 90° keine Durchfahrt;

nur für Linkslauf verfügbar

- - ● - - 13
Metrisches Innengewinde hintere Nicht als Durchfahrt geeignet ● - - - - 14

Durchfahrt

11 Flansch ISO 3019-1

Durchmesser

Nabe für Keilwelle1)

Durchmesser

045 071 100 140 180
ohne Durchgangsantrieb ● ● ● ● ● N00
82-2 (A) 5/8 Zoll 9T 16/32DP - ● ● ● ● K01
3/4 Zoll 11Z 16/32DP - ● ● ● ● K52
101-2 (B) 7/8 Zoll 13Z 16/32DP - ● ● ● ● K68
1 in 15Z 16/32DP - - ● ● ● K04
127-4 (C) 1 1/4 Zoll 14Z 12/24DP - - - ● ● K15
1 1/2 Zoll 17T12/24DP - - - - ● K16
127-2 (C) 1 1/4 Zoll 14Z 12/24DP - - - - ● K07
1 1/2 Zoll 17T 12/24DP - - - - ● K24

Steckverbinder für Magnetventile

12 Ohne Stecker (ohne Magnetspule, nur für Hydrauliksteuerungen, ohne Schilder) ● ● ● ● ●
DEUTSCH-Steckverbinder, 2-polig, ohne Löschdiode (für elektrische Steuerung) - ● ● ● ● P

• = Verfügbar ○ = Auf Anfrage - = Nicht verfügbar

Technische Daten

Größe NG 10 18 28 45 60 63 72 85 100
Geometrisches Fördervolumen pro Umdrehung Vg Max cm3 10.5 18 28 45 60 63 72 85 100
Drehzahl

Maximum1)

bei VG-Max nnom U/min 3600 3300 3000 26004) 2700 2600 2600 2500 2300
bei Vg <Vg Max 2) nmax. Zul. U/min 4320 3960 3600 3120 3140 3140 3140 3000 2500
Fluss unter nnom und VG-Max qv l/min 37 59 84 117 162 163 187 212 230
unter nE = 1500 U/min qvE l/min 15 27 42 68 90 95 108 128 150
Macht Mit Nnom, VG-Max

und Δp = 250 bar

P kW 16 25 35 49 65 68 77 89 96
unter nE= 1500 U/min PE kW 7 11 18 28 37 39 45 53 62
Drehmoment bei VG-Max

und Δp = 250 bar

M Machs gut 42 71 111 179 238 250 286 338 398
bei VG-Max

und Δp = 100 bar

M Machs gut 17 29 45 72 95 100 114 135 159
Drehsteifigkeit Antriebswelle S c Nm/rad 9200 11000 22300 37500 65500 65500 65500 143000 143000
R c Nm/rad - 14800 26300 41000 69400 69400 69400 152900 152900
U c Nm/rad 6800 8000 16700 30000 49200 49200 49200 102900 102900
W c Nm/rad - - 19900 34400 54000 54000 54000 117900 117900
P c Nm/rad 10700 - - - - - - - -
Trägheitsmoment der Triebwerksgruppe JTW Kgm2 0.0006 0.0009 0.0017 0.003 0.0056 0.0056 0.0056 0.012 0.012
Maximale Winkelbeschleunigung3) α rad/s2 8000 6800 5500 4000 3300 3300 3300 2700 2700
Fallzahl V L 0.2 0.25 0.3 0.5 0.8 0.8 0.8 1 1
Gewicht ohne Durchtrieb (ca.)

Gewicht mit Durchtrieb (ca.)

m kg 8 11.5 15 18 22 22 22 36 36
- 13 18 24 28 28 28 45 45

Bestimmung der Betriebskennlinien

Fluss qv=(Vg ∙ n ∙ ηv) / 1000 l/min
Drehmoment M=(Vg ∙ Δp) /(20 ∙ π ∙ ηhm) Machs gut
Macht P=(2π ∙ M ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt)  kW

Schlüssel

Vg  Fördervolumen pro Umdrehung in [cm3]

Δp Differenzdruck [bar]

n Drehzahl [U/min]

ηv   Volumetrischer Wirkungsgrad

ηhm  Hydraulisch-mechanischer Wirkungsgrad

ηt   Gesamtwirkungsgrad (ηt= ηv*ηhm)

1) Die Werte gelten:

- Bei einem absolutem Druck pABS = 1 bar am Sauganschluss S

- für den optimalen Viskositätsbereich von Ventscheiden = 36 bis 16 mm2/s

- mit Hydraulikflüssigkeit auf Basis von Mineralölen

2)Siehe Diagramm auf Seite 9 bei einer Geschwindigkeitserhöhung bis zu nmax adm.

3)Die Daten gelten für Werte zwischen der minimal erforderlichen und der maximal zulässigen Drehzahl. Sie gilt für externe Anregungen (z. B. Dieselmotor das 2- bis 8-fache der Drehfrequenz, Kardanwelle das doppelte der Drehfrequenz). Der Grenzwert gilt nur für eine einzelne Pumpe. Die Belastbarkeit der Verbindungsteile muss berücksichtigt werden.

Zulässige Radial- und Axialkräfte auf die Antriebswelle

Größe NG 10 18 28 45 60/63 72 85 100
Maximale Radialkraft bei a/2 FQ-max N 250 350 1200 1500 1700 1500 2000 2000
Maximale Axialkraft ±FAch, Max N 400 700 1000 1500 2000 1500 3000 3000

Zulässige Eingangs- und Durchtriebsdrehmomente

Größe 10 18 28 45 60/63 72 85 100
Drehmoment bei VG-Max und Δp = 250 bar1) MMax Machs gut 42 71 111 179 250 321 338 398
Maximales Eingangsdrehmoment an der Antriebswelle2)
S ME max Machs gut 126 124 198 319 630 630 1157 1157
∅ in 3/4 3/4 7/8 1 1 1/4 1 1/4 1 1/2 1 1/2
R ME max Machs gut - 160 250 400 650 650 1215 1215
∅ in - 3/4 7/8 1 1 1/4 1 1/4 1 1/2 1 1/2
U ME max Machs gut 60 59 105 188 306 306 628 628
∅ in 5/8 5/8 3/4 7/8 1 1 1 1/4 1 1/4
W ME max Machs gut - - 140 220 396 383 650 650
∅ in - - 3/4 7/8 1 1 1 1/4 1 1/4
P ME max Machs gut 90 - - - - - - -
∅ mm 18 - - - - - - -
Maximales Durchtriebsdrehmoment
S MD max Machs gut - 108 160 319 484 484 698 698
R MD max Machs gut - 120 176 365 484 484 698 -
U MD max Machs gut - 59 105 188 306 306 628 628
W MD max Machs gut - - 140 220 396 383 650 650

Drehmomentverteilung

 

Drehmoment an der 1. Pumpe M1
Drehmoment an der 2. Pumpe M2
Drehmoment an der 3. Pumpe M3
Eingangsdrehmoment ME=M1+M2+M3
ME < ME max
Durchtriebsdrehmoment MD=M2+M3
MD < MD max

1)Effizienz nicht berücksichtigt

2) Für Gelenkwellen ohne Radialkraft

A10VO Serie 52