Wenzhou Prance Hydraulic Equipment Co., Ltd.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
- Direct-operated spool and steel sleeve
- Electrical position feedback
- Integrated electronics (OBE)
- A1 or F1 command variants
PRANCE HYDRAULIC · PRODUCT SERIES
Direct-operated proportional spool valve with steel sleeve · Subplate-mounted electro-hydraulic control
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
Model

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Configuration review · Technical documentation · Product selection
Produktdetails
- Direct-operated spool and steel sleeve
- Electrical position feedback
- Integrated electronics (OBE)
- A1 or F1 command variants
CATEGORIES: Hydraulikventil, Proportionalventil
4WRPEH Features & Application
Direct-operated spool and steel sleeve
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
Electrical position feedback
Spool feedback concerns the valve position. Confirm whether the machine also requires separate actuator position or pressure feedback.
Integrated electronics (OBE)
Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.
A1 or F1 command variants
Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.
4WRPEH Specifications
| Series / model | 4WRPEH |
|---|---|
| Product type | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Design | Direct-operated proportional spool valve with steel sleeve |
| Circuit / selection | Subplate-mounted electro-hydraulic control |
| Listed command variants | A1: ±10 V; F1: 4–20 mA |
| Listed electrical connection | 6P+PE; confirm the approved pin assignment |
| Certification documents | Request documentation for the exact supplied unit where required |
4WRPEH Selection & Configuration
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
The series description lists A1 voltage and F1 current interfaces. Match the controller output, connector and wiring to the ordered interface. The switched-off spool position must be checked against the machine circuit; a generic CE claim is not used here as a product certification.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

4WRPEH Buying Guide
Use this sequence to prepare the 4WRPEH configuration for review and quotation.
- Select the circuit symbol and required de-energized spool position.
- State working flow, pressure and the pressure-drop condition for rated flow.
- Review spool overlap and command behavior during startup and switch-off.
- Confirm nominal size, subplate pattern, port and seal requirements.
- Match supply voltage, command input, connector and pin assignment.
- Review pilot supply, drain and feedback where the selected valve uses them.
- Approve the exact valve code, circuit drawing, quantity and documentation.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

Project Inquiries
Learn more →Send your required model, quantity, application and project requirements to discuss your inquiry.
Product inquiries · Configuration review
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your 4WRPEH Application
Send the full model code, operating duty, installation details and quantity.
Request a 4WRPEH Quotation4WRPEH Questions Before Ordering
What type of product is the 4WRPEH?
4WRPEH Proportional Valve with Integrated Electronics. Design: Direct-operated proportional spool valve with steel sleeve. Subplate-mounted electro-hydraulic control. Confirm the complete order code for the offered version.
Can a similar valve replace the 4WRPEH?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Select the circuit symbol and required de-energized spool position. State working flow, pressure and the pressure-drop condition for rated flow. Attach the nameplate, complete order code, installation drawing and required quantity.
4WRPEH Technical Data & Documents
View 4WRPEH catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Technische Daten(Für Anwendungen außerhalb dieser Parameter sprechen Sie uns bitte an!)
Allgemein
| Design | Wegeventil, direktgesteuert, mit Stahlhülse | |
| Betätigung | Proportionalmagnet mit Lageregelung, OBE | |
| Verbindungstyp | Plattenaufbau, Anschlussbild nach ISO 4401 | |
| Einbaulage | Beliebig | |
| Umgebungstemperaturbereich | ℃ | -20 …+60 |
| Lagertemperaturbereich mit UV-Schutz | ℃ | +10…+40 |
| Transporttemperatur | ℃ | -30…+80 |
| Sinustest nach DIN EN 60068-2-6 | 10…2000 Hz / maximum of 10 g/ 10 cycles/3 axes | |
| Geräuschprüfung nach DIN EN 60068-2-64 | 20…2000 Hz / 10 gRMS / 30 g peak / 30 min /3 axes | |
| Transportschock nach DIN EN 60068-2-27 | 15 g / 11 ms / 3 Achsen | |
| Gewicht | kg | 2.9 |
| Maximale relative Luftfeuchtigkeit (keine Kondensation) | % | 95 |
| Maximale Magnetoberflächentemperatur | ℃ | 150 |
| MTTFd-Wert gemäß EN ISO 13849 | Jahre | 150 (weitere Einzelheiten siehe Datenblatt 08012) |
Hydraulisch
| Hydraulikflüssigkeit | Siehe Tabelle auf Seite 6 | ||||||
| Viskositätsbereich | empfohlen | mm2/s | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ||||
| höchstzulässig | mm2/s | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| Temperaturbereich der Hydraulikflüssigkeit (durchströmt) | ℃ | -20 …+70 | |||||
| Maximal zulässiger Verschmutzungsgrad der Hydraulikflüssigkeit, Reinheitsklasse nach ISO 4406 (c) | Klasse 18/16/131) | ||||||
| Nenndurchfluss bei Δp = 35 bar pro Kante 2) | l/min | 4 | 12 | 15 | 24/25 | 40 | |
| Maximum operating pressure | - Anschlüsse A, B, P | Bar | 350 | ||||
| Port T | Bar | 250 | |||||
| Einschränkung der Verwendung hinsichtlich des Übergangs in den sicheren Zustand (Werte gelten für summierte Kante) | - Steuerschiefersymbole C3, C5, C | Bar | 350 | 350 | 350 | 350 | 160 |
| - Spulensymbole C1, C4 | Bar | 350 | 350 | 280 | 250 | 100 | |
| Leckstrom bei 100 bar | – Lineare Kennlinie L | cm3/Min. | < 180 | < 300 | – | < 500 | < 900 |
| -Gebogene Kennlinie P | cm3/Min. | < 150 | – | < 180 | < 300 | < 450 | |
statisch/dynamisch
| Hysterese | % | < 0,1 |
| Inversionsbereich | % | < 0,05 |
| Antwortsensitivität | % | < 0,05 |
| FertigungstoleranzVmax | % | < 10 |
| Temperature drift (temperature range 20℃ … 80 ℃) | Nullpunktverschiebung < 0,25 % bei Δ∂ = 10 K | |
| Druckdrift | 100 % bar | Nullpunktverschiebung < 0,15 |
| Keine Entschädigung | Ab Werk ±1 % |
| Hydraulikflüssigkeit | Klassifikation | Suitable sealing materials | Standards | |
| Mineralöle und verwandte Kohlenwasserstoffe | HL, HLP, HLPD, HVLP, HVLPD | NBR, FKM | DIN 51524 | |
| biologisch abbaubar | unlöslich in Wasser | HETG | NBR, FKM | ISO 15380 |
| HEES | FKM | |||
| löslich in Wasser | HEPG | FKM | ISO 15380 | |
| flammhemmend | wasserfrei | HFDU, HFDR | FKM | ISO 12922 |
| wasserhaltig | HFC (Fuchs HYDROTHERM 46M, Petrofer Ultra Safe 620) | NBR | ISO 12922 | |
| Important information on hydraulic fluids! ▶There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.)! ▶The flash point of the hydraulic fluid used must be 40 K higher than the maximum solenoid surface temperature. ▶Mineral oils and related hydrocarbons: – If mineral oils and related hydrocarbons are used,data sheet 90220 must be complied with! ▶Bio-degradable: – If bio-degradable hydraulic fluids are used, data sheet 90221 must be complied with! ▶Flame-resistant – water-free: – If flame-resistant, water-free hydraulic fluids are used, datasheet 90222 must be complied with! ▶Flame-resistant – containing water: The maximum pressure differential per control edge is 50 bar. Pressure pre-loading atthe tank port > 20 % of the pressure differential; otherwise,increased cavitation. Life cycle as compared to operation with mineral oil HL, HLP 50 % to 100 %. | ||||
elektrisch, integrierte Elektronik (OBE)
| Relativer Arbeitszyklus (%) | 100 (Dauerbetrieb) |
| Schutzart nach EN 60529 | IP 65 mit gesteckten und verriegelten Steckverbindern |
| Supply voltage Terminal A: Terminal B: Maximum admissible residual ripple | 24 V= At least 19 V=/maximum 36 V= 0V 2.5 Vpp |
| Maximale Leistungsaufnahme | 40 VA |
| Externe Absicherung | 2,5AT |
| Input, version A1 Terminal D: UE Terminal E: | Differenzverstärker, Ri = 100 kΩ 0…±10V 0V |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsD-E Terminal E: ID-E | Last, RSchaffhausen cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsD-E Feedback |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsTest Terminal C: | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsF-C Terminal C: IF-C | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsF-C Feedback |
| Funktionserde und Schirmung | Siehe Steckerbelegung (CE-konforme Installation) |
| Anpassung | Ab Werk kalibriert, siehe Ventilkennlinie |
| Konformität | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Related Selection Resources
Request a 4WRPEH Quotation
Tell us your required configuration, quantity and application.
Bestellcode
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 | |||
| 4 | WRP | E | H | 6 | B | - | 3X | / | / | 24 | * |
| 01 | 4 Hauptanschlüsse | 4 |
| 02 | Hochwertiges Regelventil, direktgesteuert | WRP |
| 03 | Mit integrierter Elektronik | E |
| 04 | Steuerschieber/-hülse | H |
| 05 | Größe 6 | 6 |
Steuerschiebersymbole
| 06 | Symbol | Strömungseigenschaften L | Durchflusskennlinie P | |
![]() |
||||
![]() |
● | ● | c | |
![]() |
● | ● | C1 1) | |
| ● | ● | C4 | ||
![]() |
● | ● | C3 | |
| ● | ● | C5 1) | ||
| 1) Mit den Symbolen C1 und C5: P→A:qVnom B→T:qVnom/2 P→B:qVnom/2 A→T:qVnom qVnom 2:1 nur mit Nenndurchfluss = 40 l/min |
||||
| 07 | Einbauseite des induktiven Wegaufnehmers | B |
Nenndurchfluss der Größe 6 bei 70 bar Ventildruckdifferenz (35 bar/Steuerkante)
| Strömungseigenschaften L | Durchflusskennlinie P | |||
| 8 | 04 l/min | ● | ●(Wendepunkt bei 40 %) | 04 |
| 12 l/min | ● | 12 | ||
| 15 l/min | ●(Wendepunkt bei 60 %) | 15 | ||
| 24 l/min | ● | 24 | ||
| 25 l/min | ●(Wendepunkt bei 60 %) | 25 | ||
| 40 l/min | ● | ●(Wendepunkt bei 40 %) | 40 | |
●=Lieferumfang
Strömungseigenschaften
| 09 | Linear | L |
| Knick-Kennlinie, linear | P |
| 10 | Baureihe 30 ... 39 (30 ... 39: Unveränderte Einbau- und Anschlussmaße) | 3X |
Dichtungsmaterial
| 11 | NBR-Dichtungen | M |
| FKM-Dichtungen | V |
| 12 | Versorgungsspannung der integrierten Elektronik: 24 VDC | 24 |
Schnittstellen der Steuerelektronik
| 13 | Sollwerteingabe ± 10 V | A1 |
| Sollwerteingabe 4 ... 20 mA | F1 |
| 14 | Weitere Details im Klartext |
Technische Daten(Für Anwendungen außerhalb dieser Parameter sprechen Sie uns bitte an!)
Allgemein
| Design | Wegeventil, direktgesteuert, mit Stahlhülse | |
| Betätigung | Proportionalmagnet mit Lageregelung, OBE | |
| Verbindungstyp | Plattenaufbau, Anschlussbild nach ISO 4401 | |
| Einbaulage | Beliebig | |
| Umgebungstemperaturbereich | ℃ | -20 ...+60 |
| Lagertemperaturbereich mit UV-Schutz | ℃ | +10...+40 |
| Transporttemperatur | ℃ | -30...+80 |
| Sinustest nach DIN EN 60068-2-6 | 10...2000 Hz / maximal 10 g / 10 Zyklen / 3 Achsen | |
| Geräuschprüfung nach DIN EN 60068-2-64 | 20...2000 Hz / 10 gRMS / 30 g Peak / 30 Min / 3 Achsen | |
| Transportschock nach DIN EN 60068-2-27 | 15 g / 11 ms / 3 Achsen | |
| Gewicht | kg | 2.9 |
| Maximale relative Luftfeuchtigkeit (keine Kondensation) | % | 95 |
| Maximale Magnetoberflächentemperatur | ℃ | 150 |
| MTTFd-Wert gemäß EN ISO 13849 | Jahre | 150 (weitere Einzelheiten siehe Datenblatt 08012) |
Hydraulisch
| Hydraulikflüssigkeit | Siehe Tabelle auf Seite 6 | ||||||
| Viskositätsbereich | empfohlen | mm2/s | 20...100 | ||||
| höchstzulässig | mm2/s | 10...800 | |||||
| Temperaturbereich der Hydraulikflüssigkeit (durchströmt) | ℃ | -20 ...+70 | |||||
| Maximal zulässiger Verschmutzungsgrad der Hydraulikflüssigkeit, Reinheitsklasse nach ISO 4406 (c) | Klasse 18/16/131) | ||||||
| Nenndurchfluss bei Δp = 35 bar pro Kante 2) | l/min | 4 | 12 | 15 | 24/25 | 40 | |
| Maximaler Betrieb Druck |
- Anschlüsse A, B, P | Bar | 350 | ||||
| Port T | Bar | 250 | |||||
| Einschränkung der Verwendung hinsichtlich des Übergangs in den sicheren Zustand (Werte gelten für summierte Kante) | - Steuerschiefersymbole C3, C5, C | Bar | 350 | 350 | 350 | 350 | 160 |
| - Spulensymbole C1, C4 | Bar | 350 | 350 | 280 | 250 | 100 | |
| Leckstrom bei 100 bar | – Lineare Kennlinie L | cm3/Min. | < 180 | < 300 | - | < 500 | < 900 |
| -Gebogene Kennlinie P | cm3/Min. | < 150 | - | < 180 | < 300 | < 450 | |
statisch/dynamisch
| Hysterese | % | < 0,1 |
| Inversionsbereich | % | < 0,05 |
| Antwortsensitivität | % | < 0,05 |
| FertigungstoleranzVmax | % | < 10 |
| Temperaturdrift (Temperaturbereich 20 ℃ ... 80 ℃) | Nullpunktverschiebung < 0,25 % bei Δ∂ = 10 K | |
| Druckdrift | 100 % bar | Nullpunktverschiebung < 0,15 |
| Keine Entschädigung | Ab Werk ±1 % |
1) Die für die Komponenten vorgeschriebenen Reinheitsklassen müssen in Hydrauliksystemen eingehalten werden. Eine effektive Filtration verhindert Störungen und erhöht gleichzeitig die Lebensdauer der Komponenten.
2) Strömung mit verschiedenem Δp:qx=qνnom·√(Δpx/35)
| Hydraulikflüssigkeit | Klassifikation | Geeignet Dichtungsmaterialien |
Standards | |
| Mineralöle und verwandte Kohlenwasserstoffe | HL, HLP, HLPD, HVLP, HVLPD | NBR, FKM | DIN 51524 | |
| biologisch abbaubar | unlöslich in Wasser | HETG | NBR, FKM | ISO 15380 |
| HEES | FKM | |||
| löslich in Wasser | HEPG | FKM | ISO 15380 | |
| flammhemmend | wasserfrei | HFDU, HFDR | FKM | ISO 12922 |
| wasserhaltig | HFC (Fuchs HYDROTHERM 46M), Petrofer Ultra Safe 620 |
NBR | ISO 12922 | |
| Wichtige Informationen zu Hydraulikflüssigkeiten! ▶Es kann Einschränkungen hinsichtlich der technischen Ventiltdaten (Temperatur, Druckbereich, Lebenszyklus, Wartungsintervalle usw.) geben! ▶Der Flammpunkt der verwendeten Hydraulikflüssigkeit muss 40 K über der maximalen Magnetoberflächentemperatur liegen. ▶Mineralöle und verwandte Kohlenwasserstoffe: - Bei Verwendung von Mineralölen und verwandten Kohlenwasserstoffen ist das Datenblatt 90220 zu beachten! ▶Biologisch abbaubar: - Bei Verwendung biologisch abbaubarer Hydraulikflüssigkeiten ist das Datenblatt 90221 zu beachten! ▶ Flammfest - wasserfrei - Werden schwerentflammbare, wasserfreie Hydraulikflüssigkeiten verwendet, ist das Datenblatt 90222 zu beachten! ▶Flammhemmend – wasserhaltig: Die maximale Druckdifferenz pro Steuerkante beträgt 50 bar. Druckvorbelastung am Tankanschluss > 20 % der Druckdifferenz; andernfalls kommt es zu verstärkter Kavitation. Lebensdauer im Vergleich zum Betrieb mit Mineralöl HL, HLP 50 % bis 100 %. |
||||
elektrisch, integrierte Elektronik (OBE)
| Relativer Arbeitszyklus (%) | 100 (Dauerbetrieb) |
| Schutzart nach EN 60529 | IP 65 mit gesteckten und verriegelten Steckverbindern |
| Versorgungsspannung Terminal A: Terminal B: Maximal zulässige Restwelligkeit |
24 V= mindestens 19 V= / maximal 36 V= 0V 2.5 Vss |
| Maximale Leistungsaufnahme | 40 VA |
| Externe Absicherung | 2,5AT |
| Eingabe, Version A1 Terminal D: UE Terminal E: |
Differenzverstärker, Ri = 100 kΩ 0...±10V 0V |
| Eingabe, Version F1 Terminal D: ID-E Terminal E: ID-E |
Last, RSchaffhausen = 200 Ω 4 ... (12) ... 20 mA Aktuelle Schleife ID-E Feedback |
| Maximale Differentialspannung Eingänge gegen 0 V |
|
| Testsignal, Version A1 Terminal F: UTest Terminal C: |
LVDT 0...±10V Referenz 0 V |
| Testsignal, Version F1 Terminal F: IF-C Terminal C: IF-C |
LVDT-Signal 4 ... 20 mA bei externer Last max. 200 ... 500 Ω 4 ... 20-mA-Ausgang Aktuelle Schleife IF-C Feedback |
| Funktionserde und Schirmung | Siehe Steckerbelegung (CE-konforme Installation) |
| Anpassung | Ab Werk kalibriert, siehe Ventilkennlinie |
| Konformität | CE gemäß EMV-Richtlinie 2004/108/EG Geprüft nach EN 61000-6-2 und EN 61000-6-3 |











