Wenzhou Prance Hydraulic Equipment Co., Ltd.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
- Direct-operated spool and steel sleeve
- Electrical position feedback
- Integrated electronics (OBE)
- A1 or F1 command variants
PRANCE HYDRAULIC · PRODUCT SERIES
Direct-operated proportional spool valve with steel sleeve · Subplate-mounted electro-hydraulic control
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
Model

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Configuration review · Technical documentation · Product selection
Detalles del producto
- Direct-operated spool and steel sleeve
- Electrical position feedback
- Integrated electronics (OBE)
- A1 or F1 command variants
CATEGORIES: Válvula hidráulica, Válvula proporcional
4WRPEH Features & Application
Direct-operated spool and steel sleeve
Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.
Electrical position feedback
Spool feedback concerns the valve position. Confirm whether the machine also requires separate actuator position or pressure feedback.
Integrated electronics (OBE)
Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.
A1 or F1 command variants
Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.
4WRPEH Specifications
| Series / model | 4WRPEH |
|---|---|
| Product type | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Diseño | Direct-operated proportional spool valve with steel sleeve |
| Circuit / selection | Subplate-mounted electro-hydraulic control |
| Listed command variants | A1: ±10 V; F1: 4–20 mA |
| Listed electrical connection | 6P+PE; confirm the approved pin assignment |
| Certification documents | Request documentation for the exact supplied unit where required |
4WRPEH Selection & Configuration
The 4WRPEH proportional valve is described with electrical position feedback and integrated electronics. Its technical data identifies a direct-operated spool valve with a steel sleeve. Select the required command interface and spool behavior from the complete model code.
The series description lists A1 voltage and F1 current interfaces. Match the controller output, connector and wiring to the ordered interface. The switched-off spool position must be checked against the machine circuit; a generic CE claim is not used here as a product certification.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

4WRPEH Buying Guide
Use this sequence to prepare the 4WRPEH configuration for review and quotation.
- Select the circuit symbol and required de-energized spool position.
- State working flow, pressure and the pressure-drop condition for rated flow.
- Review spool overlap and command behavior during startup and switch-off.
- Confirm nominal size, subplate pattern, port and seal requirements.
- Match supply voltage, command input, connector and pin assignment.
- Review pilot supply, drain and feedback where the selected valve uses them.
- Approve the exact valve code, circuit drawing, quantity and documentation.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

Project Inquiries
Learn more →Send your required model, quantity, application and project requirements to discuss your inquiry.
Product inquiries · Configuration review
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your 4WRPEH Application
Send the full model code, operating duty, installation details and quantity.
Request a 4WRPEH Quotation4WRPEH Questions Before Ordering
What type of product is the 4WRPEH?
4WRPEH Proportional Valve with Integrated Electronics. Design: Direct-operated proportional spool valve with steel sleeve. Subplate-mounted electro-hydraulic control. Confirm the complete order code for the offered version.
Can a similar valve replace the 4WRPEH?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Select the circuit symbol and required de-energized spool position. State working flow, pressure and the pressure-drop condition for rated flow. Attach the nameplate, complete order code, installation drawing and required quantity.
4WRPEH Technical Data & Documents
View 4WRPEH catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Datos técnicos¡Para aplicaciones fuera de estos parámetros, consúltenos!
general
| Diseño | Válvula de corredera, de acción directa, con casquillo de acero | |
| Accionamiento | Solenoide proporcional con control de posición, OBE | |
| Tipo de conexión | Montaje en placa base, patrón de orificios según ISO 4401 | |
| Posición de instalación | Cualquier | |
| Rango de temperatura ambiente | ℃ | -20 …+60 |
| Rango de temperatura de almacenamiento con protección UV | ℃ | +10…+40 |
| Temperatura de transporte | ℃ | -30…+80 |
| Prueba de vibración senoidal según la norma DIN EN 60068-2-6 | 10…2000 Hz / maximum of 10 g/ 10 cycles/3 axes | |
| Ensayo de ruido según la norma DIN EN 60068-2-64 | 20…2000 Hz / 10 gRMS / 30 g peak / 30 min /3 axes | |
| Choque de transporte según la norma DIN EN 60068-2-27 | 15g/11 ms/3 ejes | |
| Peso | kg | 2.9 |
| Humedad relativa máxima (sin condensación) | % | 95 |
| Temperatura máxima de la superficie del solenoide | ℃ | 150 |
| Valor MTTFd según la norma EN ISO 13849 | Años | 150 (para más detalles, véase la hoja de datos 08012) |
Hidráulico
| Fluido hidráulico | Ver la tabla en la página 6 | ||||||
| Rango de viscosidad | -recomendado | mm2/s | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | ||||
| máximo admisible | mm2/s | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |||||
| Rango de temperatura del fluido hidráulico (a través del cual fluye) | ℃ | -20 …+70 | |||||
| Grado máximo admisible de contaminación del fluido hidráulico, clase de limpieza según ISO 4406 (c) | Clase 18/16/131) | ||||||
| Caudal nominal a Δp = 35 bar por arista 2) | l/min | 4 | 12 | 15 | 24/25 | 40 | |
| Maximum operating pressure | - Puertos A, B, P | bar | 350 | ||||
| -Puerto T | bar | 250 | |||||
| Limitación de uso con respecto a la transición a modo seguro (los valores se aplican al flanco sumado) | - Símbolos de carrete C3, C5, C | bar | 350 | 350 | 350 | 350 | 160 |
| -Símbolos de carrete C1, C4 | bar | 350 | 350 | 280 | 250 | 100 | |
| Caudal de fuga a 100 bar | -Curva característica lineal L | cm3/min | < 180 | < 300 | – | < 500 | < 900 |
| -Curva característica curvada P | cm3/min | < 150 | – | < 180 | < 300 | < 450 | |
estático/dinámico
| Histéresis | % | < 0,1 |
| Rango de inversión | % | < 0.05 |
| Sensibilidad de respuesta | % | < 0.05 |
| Tolerancia de fabricaciónVmax | % | < 10 |
| Temperature drift (temperature range 20℃ … 80 ℃) | Desplazamiento de cero < 0,25 % con Δ∂ = 10 K | |
| Deriva de presión | 100 % bar | Desplazamiento del cero < 0,15 |
| Cero compensación | Ex fábrica ±1 % |
| Fluido hidráulico | Clasificación | Suitable sealing materials | Estándares | |
| Aceites minerales y hidrocarburos relacionados | HL, HLP, HLPD, HVLP, HVLPD | NBR, FKM | DIN 51524 | |
| Biodegradable | - insoluble en agua | HETG | NBR, FKM | ISO 15380 |
| HES | FKM | |||
| soluble en agua | HEPG | FKM | ISO 15380 | |
| Resistente a las llamas | sin agua | HFDU, HFDR | FKM | ISO 12922 |
| que contiene agua | HFC (Fuchs HYDROTHERM 46M, Petrofer Ultra Safe 620) | NBR | ISO 12922 | |
| Important information on hydraulic fluids! ▶There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.)! ▶The flash point of the hydraulic fluid used must be 40 K higher than the maximum solenoid surface temperature. ▶Mineral oils and related hydrocarbons: – If mineral oils and related hydrocarbons are used,data sheet 90220 must be complied with! ▶Bio-degradable: – If bio-degradable hydraulic fluids are used, data sheet 90221 must be complied with! ▶Flame-resistant – water-free: – If flame-resistant, water-free hydraulic fluids are used, datasheet 90222 must be complied with! ▶Flame-resistant – containing water: The maximum pressure differential per control edge is 50 bar. Pressure pre-loading atthe tank port > 20 % of the pressure differential; otherwise,increased cavitation. Life cycle as compared to operation with mineral oil HL, HLP 50 % to 100 %. | ||||
eléctrica, electrónica integrada (OBE)
| Ciclo de trabajo relativo (%) | 100 (operación continua) |
| Clase de protección según la norma EN 60529 | IP 65 con conectores enchufables montados y bloqueados |
| Supply voltage Terminal A: Terminal B: Maximum admissible residual ripple | 24 V= At least 19 V=/maximum 36 V= 0V 2.5 Vpp |
| Consumo máximo de energía | 40 VA |
| Protección por fusible, externa | 2,5 AT |
| Input, version A1 Terminal D: UE Terminal E: | Amplificador diferencial, Ri = 100 kΩ 0…±10V 0V |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsD-E Terminal E: ID-E | Carga, Rsh cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsD-E comentarios |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsprueba Terminal C: | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsF-C Terminal C: IF-C | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsF-C comentarios |
| Tierra funcional y blindaje | Ver asignación de pines (instalación compatible con CE) |
| Ajuste | Calibrado en fábrica, ver curva característica de la válvula |
| Conformidad | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Related Selection Resources
Request a 4WRPEH Quotation
Tell us your required configuration, quantity and application.
Código de pedido
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 | |||
| 4 | WRP | E | H | 6 | B | - | 3X | / | / | 24 | * |
| 01 | 4 puertos principales | 4 |
| 02 | Válvula de alta respuesta, de accionamiento directo | WRP |
| 03 | Con electrónica integrada | E |
| 04 | Carrete/manguito de control | H |
| 05 | Talla 6 | 6 |
Símbolos de carrete de control
| 06 | Símbolo | Características de flujo L | Características de flujo P | |
![]() |
||||
![]() |
● | ● | c | |
![]() |
● | ● | c1 1) | |
| ● | ● | c4 | ||
![]() |
● | ● | c3 | |
| ● | ● | c5 1) | ||
| 1) Con los símbolos C1 y C5: P→A:qVnom B→T:qVnom/2 P→B:qVnom/2 A→T:qVnom qVnom 2:1 solo con caudal nominal = 40 l/min |
||||
| 07 | Lado de instalación del transductor de posición inductivo | B |
Caudal nominal del tamaño 6 con un diferencial de presión de válvula de 70 bar (35 bar/arista de control)
| Características de flujo L | Características de flujo P | |||
| 8 | 04 l/min | ● | ●(inflexión a 40 %) | 04 |
| 12 l/min | ● | 12 | ||
| 15 l/min | ●(inflexión a 60 %) | 15 | ||
| 24 l/min | ● | 24 | ||
| 25 l/min | ●(inflexión a 60 %) | 25 | ||
| 40 l/min | ● | ●(inflexión a 40 %) | 40 | |
●=Rango de entrega
Características de flujo
| 09 | Lineal | L |
| Curva característica flexionada, lineal | P |
| 10 | Serie de componentes 30 ... 39 (30 ... 39: Dimensiones de instalación y conexión sin cambios) | 3X |
Material del sello
| 11 | Sellos NBR | M |
| Sellos de FKM | V |
| 12 | Tensión de alimentación de la electrónica integrada: 24 VCC | 24 |
Interfaces de la electrónica de control
| 13 | Entrada de valor de consigna ± 10 V | A1 |
| Entrada de valor de consigna 4 ... 20 mA | F1 |
| 14 | Más detalles en el texto plano |
Datos técnicos¡Para aplicaciones fuera de estos parámetros, consúltenos!
general
| Diseño | Válvula de corredera, de acción directa, con casquillo de acero | |
| Accionamiento | Solenoide proporcional con control de posición, OBE | |
| Tipo de conexión | Montaje en placa base, patrón de orificios según ISO 4401 | |
| Posición de instalación | Cualquier | |
| Rango de temperatura ambiente | ℃ | -20 ...+60 |
| Rango de temperatura de almacenamiento con protección UV | ℃ | +10...+40 |
| Temperatura de transporte | ℃ | -30...+80 |
| Prueba de vibración senoidal según la norma DIN EN 60068-2-6 | 10...2000 Hz / máximo de 10 g / 10 ciclos/3 ejes | |
| Ensayo de ruido según la norma DIN EN 60068-2-64 | 20...2000 Hz / 10 gRMS / 30 g pico / 30 min / 3 ejes | |
| Choque de transporte según la norma DIN EN 60068-2-27 | 15g/11 ms/3 ejes | |
| Peso | kg | 2.9 |
| Humedad relativa máxima (sin condensación) | % | 95 |
| Temperatura máxima de la superficie del solenoide | ℃ | 150 |
| Valor MTTFd según la norma EN ISO 13849 | Años | 150 (para más detalles, véase la hoja de datos 08012) |
Hidráulico
| Fluido hidráulico | Ver la tabla en la página 6 | ||||||
| Rango de viscosidad | -recomendado | mm2/s | 20...100 | ||||
| máximo admisible | mm2/s | 10...800 | |||||
| Rango de temperatura del fluido hidráulico (a través del cual fluye) | ℃ | -20 ...+70 | |||||
| Grado máximo admisible de contaminación del fluido hidráulico, clase de limpieza según ISO 4406 (c) | Clase 18/16/131) | ||||||
| Caudal nominal a Δp = 35 bar por arista 2) | l/min | 4 | 12 | 15 | 24/25 | 40 | |
| Funcionamiento máximo presión |
- Puertos A, B, P | bar | 350 | ||||
| -Puerto T | bar | 250 | |||||
| Limitación de uso con respecto a la transición a modo seguro (los valores se aplican al flanco sumado) | - Símbolos de carrete C3, C5, C | bar | 350 | 350 | 350 | 350 | 160 |
| -Símbolos de carrete C1, C4 | bar | 350 | 350 | 280 | 250 | 100 | |
| Caudal de fuga a 100 bar | -Curva característica lineal L | cm3/min | < 180 | < 300 | - | < 500 | < 900 |
| -Curva característica curvada P | cm3/min | < 150 | - | < 180 | < 300 | < 450 | |
estático/dinámico
| Histéresis | % | < 0,1 |
| Rango de inversión | % | < 0.05 |
| Sensibilidad de respuesta | % | < 0.05 |
| Tolerancia de fabricaciónVmax | % | < 10 |
| Deriva térmica (rango de temperatura 20 ℃ ... 80 ℃) | Desplazamiento de cero < 0,25 % con Δ∂ = 10 K | |
| Deriva de presión | 100 % bar | Desplazamiento del cero < 0,15 |
| Cero compensación | Ex fábrica ±1 % |
1) En los sistemas hidráulicos se deben respetar las clases de limpieza especificadas para los componentes. Una filtración eficaz evita fallos y, al mismo tiempo, aumenta el ciclo de vida de los componentes.
2) Caudal con diferente Δp:qx=qνNombre·√(Δpx/35)
| Fluido hidráulico | Clasificación | Adecuado materiales de sellado |
Estándares | |
| Aceites minerales y hidrocarburos relacionados | HL, HLP, HLPD, HVLP, HVLPD | NBR, FKM | DIN 51524 | |
| Biodegradable | - insoluble en agua | HETG | NBR, FKM | ISO 15380 |
| HES | FKM | |||
| soluble en agua | HEPG | FKM | ISO 15380 | |
| Resistente a las llamas | sin agua | HFDU, HFDR | FKM | ISO 12922 |
| que contiene agua | HFC (Fuchs HYDROTHERM 46M, Petrofer Ultra Safe 620 |
NBR | ISO 12922 | |
| ¡Información importante sobre los fluidos hidráulicos! ▶¡Puede haber limitaciones con respecto a los datos técnicos de la válvula (temperatura, rango de presión, ciclo de vida, intervalos de mantenimiento, etc.)! El punto de inflamación del líquido hidráulico utilizado debe ser 40 K superior a la temperatura máxima de la superficie del solenoide. ▶Aceites minerales e hidrocarburos relacionados: - Si se utilizan aceites minerales e hidrocarburos afines, ¡debe cumplirse la hoja de datos 90220! Biodegradable - Si se utilizan fluidos hidráulicos biodegradables, ¡se debe cumplir con la hoja de datos 90221! ▶Resistente a las llamas - sin agua: - Si se utilizan fluidos hidráulicos ignífugos y sin agua, ¡se debe cumplir con la ficha técnica 90222! ▶Resistente al fuego - contiene agua: La diferencia de presión máxima por borde de control es de 50 bar. Precarga de presión en la toma del depósito > 20 % de la diferencia de presión; de lo contrario, se produce un aumento de la cavitación. Ciclo de vida en comparación con el funcionamiento con aceite mineral HL, HLP: de 50 % a 100 %. |
||||
eléctrica, electrónica integrada (OBE)
| Ciclo de trabajo relativo (%) | 100 (operación continua) |
| Clase de protección según la norma EN 60529 | IP 65 con conectores enchufables montados y bloqueados |
| Tensión de alimentación Terminal A Terminal B: Rizado residual máximo admisible |
24 V= Al menos 19 V=/máximo 36 V= 0V 2.5 Vpp |
| Consumo máximo de energía | 40 VA |
| Protección por fusible, externa | 2,5 AT |
| Entrada, versión A1 Terminal D: UE Terminal E: |
Amplificador diferencial, Ri = 100 kΩ 0...±10V 0V |
| Entrada, versión F1 Terminal D: ID-E Terminal E: ID-E |
Carga, Rsh = 200 Ω 4 ... (12) ... 20 mA Bucle actual ID-E comentarios |
| Tensión máxima del diferencial entradas frente a 0 V |
|
| Señal de prueba, versión A1 Terminal F: Uprueba Terminal C: |
LVDT 0...±10V Referencia 0 V |
| Señal de prueba, versión F1 Terminal F: IF-C Terminal C: IF-C |
Señal LVDT 4 ... 20 mA con carga externa de 200 ... 500 Ω máximo salida de 4 a 20 mA Bucle actual IF-C comentarios |
| Tierra funcional y blindaje | Ver asignación de pines (instalación compatible con CE) |
| Ajuste | Calibrado en fábrica, ver curva característica de la válvula |
| Conformidad | CE según la Directiva EMC 2004/108/CE Probado de acuerdo con EN 61000-6-2 y EN 61000-6-3 |











