Wenzhou Prance Hydraulic Equipment Co., Ltd
A7VO Bent Axis Variable Displacement Pump
The A7VO variable pump uses a bent-axis rotary group for open-circuit drives. Changing its displacement changes delivered flow at a given drive speed. The selected controller must match the pressure, power or flow behavior required by the machine.
- Variable bent-axis rotary group
- Open-circuit hydrostatic drives
- Mobile and stationary applications
- Control devices selected by order code
PRANCE HYDRAULIC · PRODUCT SERIES
Axial piston; bent axis, variable displacement · Open circuit
The A7VO variable pump uses a bent-axis rotary group for open-circuit drives. Changing its displacement changes delivered flow at a given drive speed. The selected controller must match the pressure, power or flow behavior required by the machine.
Modèle

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.
Étude de configuration · Documentation technique · Sélection de produits
Détails du produit
- Variable bent-axis rotary group
- Open-circuit hydrostatic drives
- Mobile and stationary applications
- Control devices selected by order code
CATÉGORIES : Pompe à piston, Pompe à cylindrée variable
A7VO Features & Application
Variable bent-axis rotary group
Specify the displacement range or switching arrangement and verify performance at each required setting.
Open-circuit hydrostatic drives
Review normal running, startup and reversal where applicable. The pressure and flow requirements can differ between operating states.
Mobile and stationary applications
Compare the required flow at the actual drive speed and pressure. Check the selected variant rather than combining maxima from different rows.
Control devices selected by order code
Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.
A7VO Specifications
| Series / model | A7VO |
|---|---|
| Product type | A7VO Bent Axis Variable Displacement Pump |
| Conception | Axial piston; bent axis, variable displacement |
| Circuit / selection | Circuit ouvert |
| Published nominal sizes | 28, 55, 80, 107 and 160 |
| Listed geometric displacement | 28.1, 54.8, 80, 107 and 160 cm³/rev |
A7VO Selection & Configuration
The A7VO variable pump uses a bent-axis rotary group for open-circuit drives. Changing its displacement changes delivered flow at a given drive speed. The selected controller must match the pressure, power or flow behavior required by the machine.
Specify the operating points across the work cycle and compare them with the control characteristic. Verify inlet conditions at the highest flow demand and check the shaft, mounting flange and drain connections against the A7VO drawing.

Your Application.
The Right Configuration.
Hydraulic pumps · Hydraulic motors · Hydraulic valves
Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.
- Model review — send the full model code or an existing nameplate photograph.
- Interface matching — confirm shaft, mounting flange, rotation and ports.
- Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
- Documentation — request the relevant product data and drawings for your review.

A7VO Buying Guide
Use this sequence to prepare the A7VO configuration for review and quotation.
- Define required flow at the actual drive speed and continuous pressure.
- Identify peak pressure, duration and the work cycle.
- Confirm the selected displacement control and any auxiliary-drive requirement.
- Match rotation viewed from the shaft end, shaft, flange and ports.
- Review inlet conditions, drain routing and the installation envelope.
- Confirm fluid, viscosity, temperature, filtration and seals.
- Approve the complete model, control, drawing, quantity and delivery terms.

Selection, Documentation & Project Support

Selection Support
Learn more →Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.
Flow · Pressure · Speed · Interfaces

Technical Resources
Learn more →Review product documentation, model codes and technical data before finalizing the specification.
Datasheets · Model codes · Drawings

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Learn more →cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Configuration, Quantity & Delivery
Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.
Discuss Your A7VO Application
Send the full model code, operating duty, installation details and quantity.
Request a A7VO QuotationA7VO Questions Before Ordering
What type of product is the A7VO?
A7VO Bent Axis Variable Displacement Pump. Design: Axial piston; bent axis, variable displacement. Open circuit. Confirm the complete order code for the offered version.
Can a similar pump replace the A7VO?
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.
A7VO Technical Data & Documents
View A7VO catalog data and operating conditions
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Données techniques
| Taille | NG | 28 | 55 | 80 | 107 | 160 | ||
| Cylindrée géométrique par tour | Vg max | cm3 | 28.1 | 54.8 | 80 | 107 | 160 | |
| Maximum rotational speed 1) | À VGiga | nnom | tours par minute | 3150 | 2500 | 2240 | 2150 | 1900 |
| À Vg<0.74 x Vg max | nmax1 | tours par minute | 4250 | 3400 | 3000 | 2900 | 2560 | |
| Maximum rotational speed 2) | ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | tours par minute | 4750 | 3750 | 3350 | 3200 | 2850 | |
| Rigidité rotative | Vg max vers V g/2 | cmin | kNm/rad | 5 | 10 | 16 | 21 | 36 |
| Vg/2 à 0 (interpolé) | cmax | kNm/rad | 16 | 32 | 49 | 67 | 104 | |
| Moment d'inertie du groupe rotatif | JTW | kgm2 | 0.0042 | 0.0042 | 0.0080 | 0.0127 | 0.0253 | |
| Accélération angulaire maximale | α | rad/s2 | 35900 | 31600 | 24200 | 19200 | 15300 | |
| Volume du boîtier | V | l | 0.5 | 0.75 | 1.2 | 1.5 | 2.4 | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | m | kg | 17 | 25 | 40 | 49 | 71 | |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Définir les caractéristiques de fonctionnement
Clé
Vg cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits3] Δp = Differential pressure [bar] n = Rotational speed [rpm] ηv = Volumetric efficiency ηhm = Hydraulic-mechanical efficiency ηt = Total efficiency (ηt= ηv*ηhm)Notes
▶Theore tical values, without efficiency and tolerances;values rounded ▶Operation above the maximum values or below the minimum values may result in a loss of function, a reduced service life or in the destruction of the axial piston unit. Other permissible limit values, such as speed variation, reduced angular acceleration as a function of the frequency and the permissible angular acceleration at start (lower than the maximum angular acceleration) can be found in data sheet 90261. 1) The values are valid: – At absolute pressure Pabdos = 1 bar at suction port S – For the optimal viscosity range of vopt = 36 à 16 mm2/s -For hydraulic fluid based on mineral oils. 2) Maximum rotational speed (speed limit) for increased inlet pressure Pabdos at suction port S and Vg < Vg max , see diagram.Related Selection Resources
Request a A7VO Quotation
Tell us your required configuration, quantity and application.
Code de commande
| 01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | ||
| A7V | ○ | / | 63 | - | V | B | 01 |
Unité à pistons axiaux
| 01 | Bent-axis design, variable, nominal pressure 350 bar, maximum pressure 400 bar | A7V |
Mode de fonctionnement
| 02 | Pompe à circuit ouvert | ○ |
Taille (NG)
| 03 | Geometric displacement V2 (cm 3), see "Technical data" on page 7 | 28 | 55 | 80 | 107 | 160 |
| For sizes 250, 355 and 500, see data sheet 92203 | ||||||
Dispositif de commande
| 28 | 55 | 80 | 107 | 160 | |||||
| 04 | Power controller without power override | ● | ● | ● | ● | ● | LR | ||
| avec coupure de pression | ● | ● | ● | ● | ● | LRD | |||
| avec limiteur de course | témoin négatif | Δp = 25 bar | - | ● | ● | ● | ● | LRH1 | |
| with pressure cut-o ffand stroke limiter | témoin négatif | Δp = 25 bar | - | ● | ● | ● | ● | LRDH1 | |
| with pressure cut-o ffand load sensing | - | ● | ● | ● | ● | LRDS | |||
| Power controller with hydraulically proportional power override
(only available for clockwise rotation and with port plate 02) |
|||||||||
| avec détection de charge | - | ● | ● | - | - | LA1S | |||
| with load sensing and hydraulically proportional LS-override | - | ● | ● | - | - | LA1S5 | |||
| Régulateur de pression | ● | ● | ● | ● | ● | Dr | |||
| télécommandé | ● | ● | ● | ● | ● | GDR | |||
| avec détection de charge | - | ● | ● | ● | ● | SRD | |||
| Contrôle proportionnel hydraulique | Positive control | Δp = 10 bar | ● | ● | ● | ● | ● | HD1 | |
| with pressure cut-off, remotely controlled | Positive control | Δp = 10 bar | ● | ● | ● | ● | ● | HD1G | |
| Contrôle proportionnel électrique | Positive control | U=24V | ● | ● | ● | ● | ● | EP2 | |
Séries
| 05 | Série 6, index 3 | 63 |
Sens de rotation
| 28 to 160 | ||||
| 06 | Vu sur l'arbre de transmission | dans le sens des aiguilles d'une montre | ● | R |
| dans le sens inverse des aiguilles d'une montre | ● | L | ||
Matériau d'étanchéité
| 07 | FKM (fluoroélastomère) | V |
Arbre de transmission
| 28 to 160 | |||
| 08 | Arbre à splines DIN 5480 | ● | Z |
| Parallel keyed shaft according to DIN 6885 | ● | P | |
Bride de fixation
| 09 | ISO 3019-2; 4-hole | B |
Port plate for working lines
| 10 | SAE flange ports A and S at rear (metric fastening thread) | 01 |
| SAE flange ports A and S at side (available for power controllers LA1S and LA1S5 only, metric fastening thread) | 02 |
•= available -= not available
= programme préféré
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | ||
| A7V | ○ | / | 63 | - | V | B | 1 |
Connecteur pour solénoïdes1)
| 11 | Sans connecteur (sans solénoïde, à commande hydraulique uniquement, sans code) | |
| Connecteur moulé DEUTSCH, 2 broches - sans diode de suppression | P |
Version standard / spéciale
| 12 | Standard version (without code) | |
| Version spéciale | -S |
•= available -= not available
= programme préféré
Notes
▶Preser vation:
-Up to 12 mont hs as standard
-Up to 24 mont hs long-term
(state in plain text when ordering)
Données techniques
| Taille | NG | 28 | 55 | 80 | 107 | 160 | ||
| Cylindrée géométrique par tour | Vg max | cm3 | 28.1 | 54.8 | 80 | 107 | 160 | |
| Maximum rotational speed 1) | À VGiga | nnom | tours par minute | 3150 | 2500 | 2240 | 2150 | 1900 |
| À Vg<0.74 x Vg max | nmax1 | tours par minute | 4250 | 3400 | 3000 | 2900 | 2560 | |
| Maximum rotational speed 2) | ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | tours par minute | 4750 | 3750 | 3350 | 3200 | 2850 | |
| Flux | À VGiga cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsnom | qv | L/min | 89 | 137 | 179 | 230 | 304 |
| Puissance | À VGiga , cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsnom cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | P | kW | 52 | 80 | 105 | 134 | 177 |
| Couple | À VGiga cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | T | Rien | 156 | 305 | 446 | 596 | 891 |
| Rigidité rotative | Vg max vers V g/2 | cmin | kNm/rad | 5 | 10 | 16 | 21 | 36 |
| Vg/2 à 0 (interpolé) | cmax | kNm/rad | 16 | 32 | 49 | 67 | 104 | |
| Moment d'inertie du groupe rotatif | JTW | kgm2 | 0.0042 | 0.0042 | 0.0080 | 0.0127 | 0.0253 | |
| Accélération angulaire maximale | α | rad/s2 | 35900 | 31600 | 24200 | 19200 | 15300 | |
| Volume du boîtier | V | l | 0.5 | 0.75 | 1.2 | 1.5 | 2.4 | |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | m | kg | 17 | 25 | 40 | 49 | 71 | |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Définir les caractéristiques de fonctionnement
| Flux | qv=(Vg ∙ n ∙ ηv) / 1000 | L/min |
| Couple | T=(Vg ∙ Δp) /(20 ∙ π ∙ ηhm) | Rien |
| Puissance | P=(2π ∙ T ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt) | kW |
Clé
Vg cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits3]
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
ηv = Volumetric efficiency
ηhm = Hydraulic-mechanical efficiency
ηt = Total efficiency (ηt= ηv*ηhm)
Notes
▶Theore tical values, without efficiency and tolerances;values rounded
▶Une opération au-dessus des valeurs maximales ou en dessous des valeurs minimales peut entraîner une perte de fonction, une durée de vie réduite ou la destruction de l'unité de piston axial. D'autres valeurs limites admissibles, telles que la variation de vitesse, l'accélération angulaire réduite en fonction de la fréquence et l'accélération angulaire admissible au démarrage (inférieure à l'accélération angulaire maximale) peuvent être trouvées dans la fiche technique 90261.
1) The values are valid:
- At absolute pressure Pabdos = 1 bar at suction port S
- For the optimal viscosity range of vopt = 36 à 16 mm2/s
-For hydraulic fluid based on mineral oils.
2) Maximum rotational speed (speed limit) for increased inlet pressure Pabdos at suction port S and Vg < Vg max , see diagram.






-2.webp)
