A10VG Closed Circuit Variable Piston Pump

The A10VG variable displacement pump serves closed-circuit hydraulic drives. Moving the swashplate through neutral changes flow direction, while the boost circuit supplies replenishment and control oil according to the selected configuration.

  • Integrated boost and pilot-oil supply
  • Flow reversal through swashplate neutral
  • High-pressure relief and boost functions
  • Control and pressure cut-off options

PRANCE HYDRAULIC · PRODUCT SERIES

A10VG Closed Circuit Variable Piston Pump

Axial piston; variable swashplate · Closed circuit

The A10VG variable displacement pump serves closed-circuit hydraulic drives. Moving the swashplate through neutral changes flow direction, while the boost circuit supplies replenishment and control oil according to the selected configuration.

Modèle

✓A10VG original product photograph
A10VGAxial piston; variable swashplate
Demander un devisVoir les données techniques et la fiche technique

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Étude de configuration · Documentation technique · Sélection de produits

Détails du produit

  • Integrated boost and pilot-oil supply
  • Flow reversal through swashplate neutral
  • High-pressure relief and boost functions
  • Control and pressure cut-off options

CATÉGORIES : Pompe à piston, Pompe à cylindrée variable

A10VG Features & Application

Integrated boost and pilot-oil supply

Account for pilot or replenishment demand and the relevant pressure limits. Include filtration and the return or drain route in the circuit review.

Flow reversal through swashplate neutral

Review combined drive torque and simultaneous demand, including any additional pump connected to the drive.

High-pressure relief and boost functions

Account for pilot or replenishment demand and the relevant pressure limits. Include filtration and the return or drain route in the circuit review.

Control and pressure cut-off options

Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.

A10VG Specifications

Series / modelA10VG
Product typeA10VG Closed Circuit Variable Piston Pump
ConceptionAxial piston; variable swashplate
Circuit / selectionClosed circuit
Published nominal sizes18, 28, 45 and 63
Listed geometric displacement18, 28, 46 and 63 cm³/rev

A10VG Selection & Configuration

The A10VG variable displacement pump serves closed-circuit hydraulic drives. Moving the swashplate through neutral changes flow direction, while the boost circuit supplies replenishment and control oil according to the selected configuration.

Size the main loop and boost supply together. Include leakage replacement, flushing demand, control flow and the intended neutral behavior. Confirm relief and pressure cut-off settings from the exact control code rather than treating them as interchangeable adjustments.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Your Application.
The Right Configuration.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

A10VG Buying Guide

Use this sequence to prepare the A10VG configuration for review and quotation.

  1. Define required flow at the actual drive speed and continuous pressure.
  2. Identify peak pressure, duration and the work cycle.
  3. Confirm the selected displacement control and any auxiliary-drive requirement.
  4. Match rotation viewed from the shaft end, shaft, flange and ports.
  5. Review inlet conditions, drain routing and the installation envelope.
  6. Confirm fluid, viscosity, temperature, filtration and seals.
  7. Approve the complete model, control, drawing, quantity and delivery terms.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
Prance quality standards image from its company website

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
Prance sales team image from its company website

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Learn more →

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.


cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your A10VG Application

Send the full model code, operating duty, installation details and quantity.

Request a A10VG Quotation

A10VG Questions Before Ordering

What type of product is the A10VG?

A10VG Closed Circuit Variable Piston Pump. Design: Axial piston; variable swashplate. Closed circuit. Confirm the complete order code for the offered version.

Can a similar pump replace the A10VG?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.

A10VG Technical Data & Documents

View A10VG catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Données techniques

Taille NG 18 28 45 63
Déplacement géométrique, par révolution
variable pump Vg max   cm3 18 28 46 63
boost pump (at p = 20 bar) Vg Sp   cm3 5.5 6.1 8.6 14.9
Vitesse de rotation1) maximum at VGiga nnom min-1 4000 3900 3300 3000
limited maximum2) nmax1 min-1 4850 4200 3550 3250
intermittent maximum3) ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits min-1 5200 4500 3800 3500
minimum nmin min-1 500 500 500 500
Couple4) with VGiga et Δp =300 bar M Rien 86 134 215 301
Δp =100 bar M Rien 28.6 44.6 72 100.3
Rotary stiffness of drive shaft S c kNm/rad 20.28 32.14 53.40 78.37
T c kNm/rad – – 73.80 92.37
Moment d'inertie du groupe rotatif JTW kgm2 0.00093 0.0017 0.0033 0.0056
Accélération angulaire maximale5) α rad/s2 6800 5500 4000 3300
Volume du boîtier V l 0.45 0.64 0.75 1.1
Weight (without through drive) approx.6) m kg 18 25 27 39

Avis

▶Theoretical values, without efficiency and tolerances;values rounded ▶Operation above the maximum values or below the minimum values may result in a loss of function,a reduced service life or in the destruction of the axial piston unit. Prance recommends testing the loads by means of experiment or calculation /simulation and comparison with the permissible values.

Définir les caractéristiques de fonctionnement

Clé

Vg  Déplacement par révolution en [cm3] Δp  Differential pressure [bar] n   Rotational speed [rpm] ηv   Volumetric efficiency ηhm  Hydraulic-mechanical efficiency ηt   Efficacité totale (ηt= ηv*ηhm) 1)The values are applicable: – for the optimum viscosity range from Vopt = 36 … 16 mm2/s – for hydraulic fluid based on mineral oils (for HF hydraulic fluids,observe the technical data in 90225) 2)Valid at half corner power (e.g. at Vg max and pi/2) 3) Valid at Ap = 70 … 150 bar or Ap < 300 bar and t < 0.1 s 4)Without boost pump 5)The data are valid for values between the minimum required and maximum permissible rotational speed. Valid for external excitation (e. g. diesel engine 2 to 8 times rotary frequency; cardan shaft twice the rotary frequency). The limit value is only valid for a single pump. The load capacity of the connection parts must be considered. 6)Weight may vary by equipment.

Permissible radial and axial loading of the drive shaft

Taille NG 18 28 28 45 45 63 63
Arbre de transmission in 7/8 1 1 1/4 1 1 1/4 1 1/4 1 3/8
Maximum radial force at distance a (to the shaft collar) cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Fq max N 1300 2500 2500 3600 3600 5000 5000
a mm 16.5 17.5 17.5 17.5 17.5 17.5 17.5
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits +Fax max N 973 987 987 1500 1500 2200 2200
-Fax max N 973 987 987 1500 1500 2200 2200

Avis

▶The axial and radial loading generally influence the bearing service life. ▶Special requirements apply in the case of belt drive and cardan shaft. Please contact us.

couples d'entrée et de transmission admissibles

Taille NG 18 28 45 63
Couple d'entrée maximal sur l'arbre d'entraînement2)
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits S ME max Rien 192 314 314 602
in 7/8 1 1 1 1/4
T ME max Rien – 602 602 970
in – 1 1/4 1 1/4 1 3/8
Couple maximal en traversée ME max Rien 112 220 314 439

Répartition des couples

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Couple d'entrée ME=M1+M2+M3
ME < ME max
Couple en traversée MD=M2+M3
MD < MD max
1) Efficiency not considered 2) For drive shafts free of radial force
Watch A10VG Product Video
A10VG product video

Request a A10VG Quotation

Tell us your required configuration, quantity and application.

Démo du formulaire de contact
A10VG original product photograph

Code source

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22
A10V G / 10 - N C

Unité à pistons axiaux

01 Conception à plateau oblique, variable, pression nominale 350 bar, pression maximale 400 bar A10V

Mode de fonctionnement

02 Pompe, circuit fermé G

Taille (NG)

03 Cylindrée géométrique, voir " Données techniques " à la page 8 18 28 45 63

Dispositif de commande

18 28 45 63
04 Proportional control

hydraulique

pilot-pressure related, with inlet filtration in P and X1/X2 ● ● ● ● HD3
mechanical servo ● ● ● ● Devoir
Commande automatique, liée à la vitesse1) U=12V - ● ● ● DA1
U=24V - ● ● ● DA2
Hydraulic control direct operated ● ● ● ● DG
Commande proportionnelle, électrique with proportional solenoid with inlet filtration in P and X1/X2 U=12V ● ● ● ● ÉP3
U=24V ● ● ● ● EP4
Régulation à deux points, électrique with switching solenoid U=12V ● ● ● ● EZ1
U=24V ● ● ● ● EZ2
Electric control, direct operated

two pressure reducing valves (FTDRE)

U=12V - ● ● - ET3
U=24V - ● ● - ET4
Electric pressure controller,

negative control,

with 4/2 directional valve and one pressure reducing valve1)

de-energized, stroking chamber is controlled via X1 U=24V - ● ● ● ED2
de-energized, stroking chamber is controlled via X2 U=24V - ● ● ● ED4

Coupure par pression

18 28 45 63
05 Without pressure cut-off (without code) ● ● ● ●
With pressure cut-off - ● ● ● D

Contacteur de position neutre

18 28 45 63
06 Sans interrupteur de position neutre (sans code) ● ● ● ●
Neutral position switch with DEUTSCH connector (only for HW control) ● ● ● ● L

Limiteur de course mécanique2)

18 28 45 63
07 Sans limiteur de course mécanique (sans code) ● ● ● ●
Limiteur de course mécanique, réglable de l'extérieur ● ● ● ● L

Orifice de pression de la chambre de manœuvre2)

18 28 45 63
08 Sans actionner l'orifice de pression de chambre X3, X4(sans code) ● ● ● ●
Stroking chamber pressure portX3, X4 ● ● ● ● L

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits     = programme préféré

1) Only possible in combination with pressure cut-off(DA.D..., ED.D...)

2) Not available in combination with DG control device

DA control valve for NG28 ... 63

HD Devoir DG DA EP Facile ET ED
09 Sans vanne de régulation DA ● ● ● - ● ● ● ● 1
soupape de commande DA, réglage fixe ● ● ● ● ● - - - 2
DA control valve, mechanically adjustable,

with position lever

direction of actuation, counter-clockwise ● ● ● ● ● - - - 3L
sens d'actionnement, horaire ● ● ● ● ● - - - 3R
distributeur DA, réglage fixe, orifices pour dispositif de commande pilote ● ● - ● ● - - - 7
DA control valve, fixed setting, and hydraulic inch valve mounted,control with mineral oil - - - ● - - - - 8

Séries

10 Series 1, index 0 10

Sens de rotation

18 28 45 63
11 Vu sur l'arbre de transmission dans le sens des aiguilles d'une montre ● ● ● ● R
dans le sens inverse des aiguilles d'une montre ● ● ● ● L

Matériau d'étanchéité

18 28 45 63
12 NBR (nitrile rubber), shaft seal made of FKM (fluoroelastomer) ● ● ● ● N

Arbre de transmission

18 28 45 63
13 Arbre cannelé

ANSI B92.1a-1976

pour pompe unique ● ● ● ● S
for combination pump ● ● ● ● T

Bride de fixation

18 28 45 63
14 SAE J744 à deux trous ● ● ● ● C

Port en eau profonde

15 Port thread: Metric with profile sealing ring sealing according to DIN 3852

Fastening thread at the SAE working port and through drive: Metric according to DIN 13

18 28 45 63
SAE working port A and B, same side left cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits - ● ● ● 10
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

- ● ● ● 13
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

18 28 45 63
Threaded port A and B, same side right cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits ● - - - 16

Boost pump

18 28 45 63
16 Without integrated boost pump sans entraînement direct ● ● ● ● N
with through drive ● ● ● ● K
Integrated boost pump with and without through drive ● ● ● ● F

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits     = programme préféré

Drive3)

18 28 45 63
17 Without through drive, only for version N and F (position 16) ● ● ● ● 00
Bride SAE J744 Moyeu pour arbre cannelé4)
82-2 (A) 5/8 po 9T 16/32DP ● ● ● ● 01
3/4 po 11T 16/32DP - ● ● ● 52
101-2(B) 7/8 in 13T 16/32DP ● ● ● ● 02
1 po 15T 16/32DP - ● ● ● 04
127-2 (C) 1 1/4 in 14T 12/24DP - - - ● 07

High-pressure relief valve

Setting range ΔpHD 18 28 45 63
18 High-pressure relief valve

direct operated, fixed setting

250 ... 320 bar without bypass ● ● ● ● 3
with bypass ● ● ● ● 5
100 ... 250 bar without bypass - ● ● ● 4
with bypass - ● ● ● 6

Filtration boost circuit/external boost pressure supply

18 28 45 63
19 Filtration in the boost pump suction line ● ● ● ● S
Filtration in the boost pump pressure line

Ports for external boost circuit filtration (Fe and G (Fa))

- ●5) ●5) ● D
External boost pressure supply (on version without integrated boost pump - N, K) ● ● ● ● E

Connecteur pour solénoïdes6)

18 28 45 63
20 Without connector (without code), only with purely hydraulic controls ● ● ● ●
DEUTSCH molded connector

2-pin, DT04-2P

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits ● ● ● ● P
with suppressor diode (only for EZ, DA and ED switching solenoid) ● ● ● ● Q

Flushing valve

18 28 45 63
21 Without flushing valve (without code) ● ● ● ●
Flushing valve SAE connection diagram, metric mounting ● ● ● ● 1
metric threaded ports ● ● ● ● 3

Standard/special version

22 Version standard sans code
Version spéciale -S

• = disponible ○ = sur demande - = non disponible     = programme préféré

Avis

▶Note the project planning notes on page 59!

En plus du code type, veuillez spécifier les données techniques pertinentes lors de votre commande.

▶Please note that not all type code combinations are available although the individual functions are marked as being available.

3)Specifications for version with integrated boost pump,please contact us for version without boost pump

4)Hub for splined shaft according to ANSI B92.1a-1976(drive shaft allocation according to SAE J744)

5) Pressure filtration is not possible in connection with DA control valve

Les connecteurs pour d'autres composants électriques peuvent différer.

Données techniques

Taille NG 18 28 45 63
Déplacement géométrique, par révolution
variable pump Vg max

 

cm3 18 28 46 63
boost pump (at p = 20 bar) Vg Sp

 

cm3 5.5 6.1 8.6 14.9
Vitesse de rotation1) maximum at VGiga nnom min-1 4000 3900 3300 3000
limited maximum2) nmax1 min-1 4850 4200 3550 3250
intermittent maximum3) ncURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits min-1 5200 4500 3800 3500
minimum nmin min-1 500 500 500 500
Flux à nnom et VGiga qv L/min 72 109 152 189
Puissance4) à nnom,  VGiga et Δp =300 bar P kW 36 54.6 75.9 94.5
Couple4) with VGiga et Δp =300 bar M Rien 86 134 215 301
Δp =100 bar M Rien 28.6 44.6 72 100.3
Rotary stiffness of drive shaft S c kNm/rad 20.28 32.14 53.40 78.37
T c kNm/rad - - 73.80 92.37
Moment d'inertie du groupe rotatif JTW kgm2 0.00093 0.0017 0.0033 0.0056
Accélération angulaire maximale5) α rad/s2 6800 5500 4000 3300
Volume du boîtier V l 0.45 0.64 0.75 1.1
Weight (without through drive) approx.6) m kg 18 25 27 39

Avis

▶Valeurs théoriques, sans efficacité ni tolérances ; valeurs arrondies

▶Operation above the maximum values or below the minimum values may result in a loss of function,a reduced service life or in the destruction of the axial piston unit. Prance recommends testing the loads by means of experiment or calculation /simulation and comparison with the permissible values.

Définir les caractéristiques de fonctionnement

Flux qv=(Vg ∙ n ∙ ηv) / 1000 L/min
Couple M=(Vg ∙ Δp) /(20 ∙ π ∙ ηhm) Rien
Puissance P=(2π ∙ M ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt)  kW

Clé

Vg  Déplacement par révolution en [cm3]

Δp  Pression différentielle [bar]

n   Vitesse de rotation [tr/min]

ηv   Efficacité volumétrique

ηhm  Efficacité hydraulico-mécanique

ηt   Efficacité totale (ηt= ηv*ηhm)

1)The values are applicable:

- for the optimum viscosity range from Vopt = 36 ... 16 mm2/s

- for hydraulic fluid based on mineral oils (for HF hydraulic fluids,observe the technical data in 90225)

2)Valid at half corner power (e.g. at Vg max and pi/2)

3) Valid at Ap = 70 ... 150 bar or Ap < 300 bar and t < 0.1 s

4)Without boost pump

5)The data are valid for values between the minimum required and maximum permissible rotational speed.

Valid for external excitation (e. g. diesel engine 2 to 8 times rotary frequency; cardan shaft twice the rotary frequency).

The limit value is only valid for a single pump.

The load capacity of the connection parts must be considered.

6)Weight may vary by equipment.

Permissible radial and axial loading of the drive shaft

Taille NG 18 28 28 45 45 63 63
Arbre de transmission in 7/8 1 1 1/4 1 1 1/4 1 1/4 1 3/8
Maximum radial

force at distance a

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Fq max N 1300 2500 2500 3600 3600 5000 5000
a mm 16.5 17.5 17.5 17.5 17.5 17.5 17.5
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits +Fax max N 973 987 987 1500 1500 2200 2200
-Fax max N 973 987 987 1500 1500 2200 2200

Avis

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

couples d'entrée et de transmission admissibles

Taille NG 18 28 45 63
Couple à VGiga cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits1) M Rien 86 134 220 301
Couple d'entrée maximal sur l'arbre d'entraînement2)
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits S ME max Rien 192 314 314 602
in 7/8 1 1 1 1/4
T ME max Rien - 602 602 970
in - 1 1/4 1 1/4 1 3/8
Couple maximal en traversée ME max Rien 112 220 314 439

Répartition des couples

Couple à la première pompe M1
Couple à la deuxième pompe M2
Couple à la troisième pompe M3
Couple d'entrée ME=M1+M2+M3
ME < ME max
Couple en traversée MD=M2+M3
MD < MD max

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

A10VG