A11VO Open Circuit Variable Piston Pump

The A11VO variable pump is offered for open-circuit mobile hydraulics. Its family documentation includes A11VO and charged A11VLO arrangements, so speed and inlet conditions must be attached to the actual version rather than combined into one family maximum.

  • Mobile-application focus
  • Self-priming or charged arrangements
  • Through-drive configuration available
  • Variable displacement and multiple controls

PRANCE HYDRAULIC · PRODUCT SERIES

A11VO Open Circuit Variable Piston Pump

Axial piston; variable swashplate · Open circuit

The A11VO variable pump is offered for open-circuit mobile hydraulics. Its family documentation includes A11VO and charged A11VLO arrangements, so speed and inlet conditions must be attached to the actual version rather than combined into one family maximum.

Modèle

✓A11VO original product photograph
A11VOAxial piston; variable swashplate
Demander un devisVoir les données techniques et la fiche technique

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Étude de configuration · Documentation technique · Sélection de produits

Détails du produit

  • Mobile-application focus
  • Self-priming or charged arrangements
  • Through-drive configuration available
  • Variable displacement and multiple controls

CATÉGORIES : Pompe à piston, Pompe à cylindrée variable

A11VO Features & Application

Mobile-application focus

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

Self-priming or charged arrangements

Specify the full MS order code, installation drawing and operating duty so the quotation can identify the proposed configuration.

Through-drive configuration available

Review combined drive torque and simultaneous demand, including any additional pump connected to the drive.

Variable displacement and multiple controls

Match the complete control option and its command requirements to the existing controller. Similar housings can use different control arrangements.

A11VO Specifications

Series / modelA11VO
Product typeA11VO Open Circuit Variable Piston Pump
ConceptionAxial piston; variable swashplate
Circuit / selectionCircuit ouvert
Published family sizes40, 60, 75, 95, 130, 145, 190 and 260; version-dependent
Inlet arrangementConfirm self-priming, pressurized tank or charged version

A11VO Selection & Configuration

The A11VO variable pump is offered for open-circuit mobile hydraulics. Its family documentation includes A11VO and charged A11VLO arrangements, so speed and inlet conditions must be attached to the actual version rather than combined into one family maximum.

Review the required flow and power over the machine work cycle, including any pump mounted on the through drive. Specify the inlet arrangement, control and simultaneous auxiliary demand. Confirm whether the quoted unit is A11VO or A11VLO before applying a speed limit.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Your Application.
The Right Configuration.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

A11VO Buying Guide

Use this sequence to prepare the A11VO configuration for review and quotation.

  1. Define required flow at the actual drive speed and continuous pressure.
  2. Identify peak pressure, duration and the work cycle.
  3. Confirm the selected displacement control and any auxiliary-drive requirement.
  4. Match rotation viewed from the shaft end, shaft, flange and ports.
  5. Review inlet conditions, drain routing and the installation envelope.
  6. Confirm fluid, viscosity, temperature, filtration and seals.
  7. Approve the complete model, control, drawing, quantity and delivery terms.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
Prance quality standards image from its company website

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
Prance sales team image from its company website

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Learn more →

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.


cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your A11VO Application

Send the full model code, operating duty, installation details and quantity.

Request a A11VO Quotation

A11VO Questions Before Ordering

What type of product is the A11VO?

A11VO Open Circuit Variable Piston Pump. Design: Axial piston; variable swashplate. Open circuit. Confirm the complete order code for the offered version.

Can a similar pump replace the A11VO?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.

A11VO Technical Data & Documents

View A11VO catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Données techniques

Table of values (theoretical values, without efficiency levels and tolerances; values rounded)

Taille A11VO 40 60 75 95 130 190 190 260
Déplacement Vg max cm3 42 58.5 74 93.5 130 190 190 260
Vg min cm3 0 0 0 0 0 0 0 0
Vitesse
maximum at Vg max1) maximum at Vg ≤ Vg max1) nmax tours par minute 3000 2700 2550 2350 2100 2200 2100 1800
nmax1 tours par minute 3500 3250 3000 2780 2500 2500 2100 2300
Rigidité rotative Z shaft Nm/rad 88894 102440 145836 199601 302495 302495 346190 686465
P shaft Nm/rad 87467 107888 143104 196435 312403 312403 383292 653835
S shaft Nm/rad 58347 86308 101921 173704 236861 236861 259773 352009
T shaft Nm/rad 74476 102440 12560 – – – 301928 567115
Moment d'inertie pour le groupe rotatif JTW Kgm2 0.0048 0.0082 0.0115 0.0173 0.0318 0.0341 0.055 0.0878
Angular acceleration, max4) α rad/s2 22000 17500 15000 13000 10500 9000 6800 4800
Filling capacity V I 1.1 1.35 1.85 2.1 2.9 2.9 3.8 4.6
Masse (approximative) m kg 32 40 45 53 66 76 95 125
Taille A11VO 130 145 190 260
Déplacement Vg max cm3 130 145 193 260
Vg min cm3 0 0 0 0
Vitesse
maximum at Vg max1) maximum at Vg ≤ Vg max1) nmax tours par minute 2500 2500 2500 2300
nmax1 tours par minute 2500 2500 2500 2300
Rigidité rotative Z shaft Nm/rad 302495 302495 346190 686465
P shaft Nm/rad 312403 312403 383292 653835
S shaft Nm/rad 236861 236861 259773 352009
T shaft Nm/rad – – 301928 567115
Moment d'inertie pour le groupe rotatif JTW Kgm2 0.0337 0.036 0.0577 0.0895
Angular acceleration, max4) α rad/s2 10500 9000 6800 4800
Filling capacity V I 2.9 2.9 3.8 4.6
Masse (approximative) m kg 72 73 104 138
1 )The values apply at absolute pressure (Pabdos) 1 bar at the suction port S and mineral hydraulic fluid. 2)The values apply at absolute pressure (Pabdos) of at least 0.8 bar at the suction port S and mineral hydraulic fluid. 3) The values apply at Vs Vg max or in case of an increase in the inlet pressure Pabdos at the suction port S (see diagram page 6) 4) – The area of validity is situated between 0 and the maximum permissible speed.It applies for external stimuli (e.g. engine 2-8 times rotary frequency, cardan shaft twice the rotary frequency). -The limit value applies for a single pump only. -The loading on the connection parts has to be considered. Caution: Exceeding the permissible limit values could cause a loss of function, reduced service life or the destruction of the axial piston unit. The permissible values can be determined by calculation.

Permissible radial and axial loadirng on drive shaft

The values stated are maximum data and not permissible for continuous operation
Taille 40 60 75 95 130 190 190 260
Radial force, max.at distance a, b,c(from shaft collar)   Fq max a N mm 3600 5000 6300 8000 11000 11000 16925 22000
17.5 17.5 20 20 22.5 22.5 26 29
Fq max b N mm 2891 4046 4950 6334 8594 8594 13225 16809
30 30 35 35 40 40 46 50
Fq max c N mm 2416 3398 4077 5242 7051 7051 108500 13600
42.5 42.5 50 50 57.5 57.5 66 71
Force axiale, max.   ±Fax max N 1500 2200 2750 3500 4800 4800 6000 4150

Permissible input and through drive torques

Taille 40 60 75 95 130 190 190 260
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.2) at shaft end P Shaft key DN 6885
TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 468 648 824 1044 1448 1448 2226 2787
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Φ55 Φ60
at Z shaft end DIN 5480 TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 912 912 1460 2190 3140 3140 3140 5780
W35 W35 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits W50 W50 W50 W60
at S shaft end ANSI B92.1a-1976 (SAE J744) TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 314 602 602 1640 1640 1640 1640 1640
1 po 1 1/4 po 1 1/4 po 1 3/4in 1 3/4in 1 3/4in 1 3/4in 1 3/4in
at T shaft end ANSI B92.1a-1976 (SAE J744) TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 602 970 970 – – – 2670 4070
1 1/4 in 1 3/8 in 1 3/8 in – – – 2 in 2 1/4 in
Through drive torque, max.3) TD perm. Rien 314 521 660 822 1110 1110 1760 2065
1)Efficiency not considered 2) For drive shafts with no radial force 3) Observe max. input torque for shaft S!

Torque distribution

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Determining the nominal value

Vg = Displacement per revolution in cm3 Δp = Differential pressure in bar n = Speed in rpm ηv = Volumetric efficiency ηhm = Mechanical-hydraulic efficiency ηt = Overall efficiency (nt= nv* nhm)
Watch A11VO Product Video
A11VO product video

Request a A11VO Quotation

Tell us your required configuration, quantity and application.

Démo du formulaire de contact
A11VO original product photograph

Code de commande / Programme standard

A11V ○ / 1 - N
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

Unité à pistons axiaux

01 Conception à plateau oblique, variable, pression nominale 350 bar, pression maximale 400 bar A11V

Pompe de charge (turbine)

02 sans pompe de charge ● ● ● ● ● ● ● ●
avec pompe de charge - - - - ● ● ● ● L

Opération

03 Pompe à circuit ouvert ○

Taille

04 ≈Déplacement Yg maxen cm3 40 60 75 95 130 145 190 260

Unité de commande

05 Contrôle de l'alimentation LR ● ● ● ● ● ● ● ● LR
avec dérogation télé-détection croisée négatif LR C ● ● ● ● ● ● ● ● LP.C
lié à la haute pression négatif LR3 ● ● ● ● ● ● ● ● LR3
lié à la pression de pilotage négatif LG1 ● ● ● ● ● ● ● ● LG1
positif LG2 ● ● ● ● ● ● ● ● LG2
électrique U=12V négatif LE1 ○ ○ ○ ● ● ● ● ● LE1
U=24V négatif LE2 ○ ● ● ● ● ● ● ● LE2
avec coupure de pression D ● ● ● ● ● ● ● ● L.D.
hydraulique, à 2 étages E ● ● ● ● ● ● ● ● L.E.
hydraulique, télécommandé G ● ● ● ● ● ● ● ● L..G.
avec détection de charge S ● ● ● ● ● ● ● ● L...S
électrique, commande manuelle prioritaire, 24 V S2 ○ ○ ○ ● ● ● ● ● L...S2
commande hydraulique, prop. S5 ○ ○ ○ ● ● ● ● ● L...S5
avec limiteur de course négatif

caractéristique

Δp = 25 bar H1 ● ● ● ● ● ● ● ● L...H1
Δp = 10 bar H5 ● ● ● ● ● ● ● ● L...H5
positif

caractéristique

Δp = 25 bar H2 ● ● ● ● ● ● ● ● L...H2
Δp = 10 bar H6 ● ● ● ● ● ● ● ● L...H6
U=12V U1 ● ● ● ● ● ● ● ● L...U1
U=24V U2 ● ● ● ● ● ● ● ● L...U2
Contrôle de la pression Dr ● ● ● ● ● ● ● ● Dr
avec détection de charge SRD ● ● ● ● ● ● ● ● SRD
télécommandé GDR ● ● ● ● ● ● ● ● GDR
pour un fonctionnement en parallèle LMR ● ● ● ● ● ● ● ● LMR
Commande hydraulique, asservie à la pression de pilotage (positive characteristic) Δp = 10 bar HD1 ● ● ● ● ● ● ● ● HD1
Δp=25 bar HD2 ● ● ● ● ● ● ● ● HD2
avec coupure de pression D ● ● ● ● ● ● ● ● HD.D
with pressure cut-off, remote controlled G ○ ● ○ ○ ○ ○ ● ● HD.G
Electric control with proportional solenoid (positive characteristic) U=12V EP1 ● ● ● ● ● ● ● ● EP1
U=24V EP2 ● ● ● ● ● ● ● ● EP2
avec coupure de pression D ● ● ● ● ● ● ● ● EP.D
with pressure cut-off, remote control G ● ● ● ● ● ● ● ● EP.G

In case of controls with several additional functions, observe the order of the columns, only one option per column is possible (e.g. LRDCH2). The following combinations are not available for the power control: LRDS2, LRDS5, L.. GS, L.. GS2, L. GS5EC and the combination L..DG in conjunction with the stroke limiters H1, H2, H5, H6, U1 and U2.

Séries

06 1

Index

07 Size 40 ... 130 0
Size 145...260 1

Sens de rotation

08 Vu du côté de l'arbre dans le sens des aiguilles d'une montre R
dans le sens inverse des aiguilles d'une montre L

Joints d'étanchéité

09 NBR (caoutchouc nitrile), anneau d'étanchéité d'arbre en FKM (caoutchouc fluoré) N

Extrémité de l'arbre

10 40 60 75 95 130 145 190 260
Splined shaft DIN 5480 for single and combination pump ● ● ● ● ● ● ● ● Z
Parallel keyed shaft DIN 6885 ● ● ● ● ● ● ● ● P
Splined shaft ANSI B92.1a-1976 pour pompe unique ● ● ● ● ● ● ● ● S
for combination pump ● ● ● _1) _1) _1) ● ● T

Bride de fixation

11 40 60 75 95 130 145 190 260
SAE J744-2-hole ● ● - - - - - - C
SAE J744-4-hole - - ● ● ● ● ● ● D
SAE J6172) (SAE 3) - - - ● ● ● ● - G

Ports de ligne de service

12 Pressure and suction port SAE, at side, opposite side

(with metric fastening threads)

40 60 75 95 130 145 190 260
● ● ● ● ● ● ● ● 12

Drive

40 60 75 95 130 145 190 260
13 Bride SAE J7443) Coupler for splined shaft
- - ● ● ● ● ● ● ● ● N00
82-2 (A) 5/8 pouce 9T 16/32DP (A) ● ● ● ● ● ● ● ● K01
3/4in 11T 16/32DP (A-B) ○ ● ○ ● ● ● ○ ○ K52
101-2 (B) 7/8 po 13T 16/32DP (B) ● ● ● ● ● ● ● ● K02
1 po 15T 16/32DP (B-B) ● ● ● ● ● ● ● ● K04
W35 2x30x16x9g ● ● ● ● ● ● ● ● K79
127-2 (C)4) 1 1/4in 14T 12/24DP (C) - ● ● ● ● ● ● ● K07
1 1/2in 17T 12/24DP (C-C) - - - ● ● ● ● ● K24
W30 2x30x14x9g - ● ● ● ● ● ● ● K80
W35 2x30x16x9g - ● ● ● ● ● ● ● K61
152-4 (D) 1 1/4in 14T 12/24DP (C) - - ● ● ● ● ● ● cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits 13T 8/16DP (D) - - - - ● ● ● ● K17
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits - - ● ● ● ● ● ● cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits - - - ● ● ● ● ● cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
W50 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits - - - - ● ● ● ● K83
165-4 (E) cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits 13T 8/16DP (D) - - - - - - ● ● K72
W50 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits - - - - - - ● ● K84
W60 2x30x28x9g - - - - - - - ● K67

Swivel angle indicator

14 40 60 75 95 130 145 190 260
without swivel angle indicator (no symbol) ● ● ● ● ● ● ● ●
with optical swivel angle indicator ● - ● ● ● ● ● ● v
with electric swivel angle sensor ● - ● ● ● ● ● ● R

Connecteur pour solénoïdes

15 40 60 75 95 130 145 190 260
Connecteur moulé DEUTSCH, 2 broches - sans diode de suppression ● ● ● ● ● ● ● ● P

Standard/special version

16 Version standard without symbol
combined with attachment part or attachment pump -K
Version spéciale -S
combined with attachment part or attachment pump cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

1) S-shaft suitable for combination pump!

2) To fit the flywheel case of the combustion engine

3)22-hole;44-hole

4) Size 190 and 260 with 2 + 4-hole flange

• = disponible ○ = sur demande - = non disponible      = programme préféré

Données techniques

Table of values (theoretical values, without efficiency levels and tolerances; values rounded)

Taille A11VO 40 60 75 95 130 190 190 260
Déplacement Vg max cm3 42 58.5 74 93.5 130 190 190 260
Vg min cm3 0 0 0 0 0 0 0 0
Vitesse
maximum at Vg max1)

maximum at Vg ≤ Vg max1)

nmax tours par minute 3000 2700 2550 2350 2100 2200 2100 1800
nmax1 tours par minute 3500 3250 3000 2780 2500 2500 2100 2300
Flux

à nmax and vGiga

qv max L/min 126 158 289 220 273 319 405 468
Flow at

qv max et Δp = 350 bar

Pmax kW 74 92 110 128 159 186 236 273
Torque at

vg max et Δp = 350 bar

Tmax Rien 234 326 412 521 724 808 1075 1448
Rigidité rotative Z shaft Nm/rad 88894 102440 145836 199601 302495 302495 346190 686465
P shaft Nm/rad 87467 107888 143104 196435 312403 312403 383292 653835
S shaft Nm/rad 58347 86308 101921 173704 236861 236861 259773 352009
T shaft Nm/rad 74476 102440 12560 - - - 301928 567115
Moment d'inertie pour le groupe rotatif JTW Kgm2 0.0048 0.0082 0.0115 0.0173 0.0318 0.0341 0.055 0.0878
Angular acceleration, max4) α rad/s2 22000 17500 15000 13000 10500 9000 6800 4800
Filling capacity V I 1.1 1.35 1.85 2.1 2.9 2.9 3.8 4.6
Masse (approximative) m kg 32 40 45 53 66 76 95 125
Taille A11VO 130 145 190 260
Déplacement Vg max cm3 130 145 193 260
Vg min cm3 0 0 0 0
Vitesse
maximum at Vg max1)

maximum at Vg ≤ Vg max1)

nmax tours par minute 2500 2500 2500 2300
nmax1 tours par minute 2500 2500 2500 2300
Flux

à nmax and vGiga

qv max L/min 325 363 483 598
Flow at

qv max et Δp = 350 bar

Pmax kW 190 211 281 349
Torque at

vg max et Δp = 350 bar

Tmax Rien 724 808 1075 1448
Rigidité rotative Z shaft Nm/rad 302495 302495 346190 686465
P shaft Nm/rad 312403 312403 383292 653835
S shaft Nm/rad 236861 236861 259773 352009
T shaft Nm/rad - - 301928 567115
Moment d'inertie pour le groupe rotatif JTW Kgm2 0.0337 0.036 0.0577 0.0895
Angular acceleration, max4) α rad/s2 10500 9000 6800 4800
Filling capacity V I 2.9 2.9 3.8 4.6
Masse (approximative) m kg 72 73 104 138

1 )The values apply at absolute pressure (Pabdos) 1 bar at the suction port S and mineral hydraulic fluid.

2)The values apply at absolute pressure (Pabdos) of at least 0.8 bar at the suction port S and mineral hydraulic fluid.

3) The values apply at Vs Vg max or in case of an increase in the inlet pressure Pabdos at the suction port S (see diagram page 6)

4) - The area of validity is situated between 0 and the maximum permissible speed.It applies for external stimuli (e.g. engine 2-8 times rotary frequency, cardan shaft twice the rotary frequency).

-The limit value applies for a single pump only.

-The loading on the connection parts has to be considered.

Caution:

Exceeding the permissible limit values could cause a loss of function, reduced service life or the destruction of the axial piston unit. The permissible values can be determined by calculation.

Permissible radial and axial loadirng on drive shaft

The values stated are maximum data and not permissible for continuous operation

Taille 40 60 75 95 130 190 190 260
Radial force, max.at distance a, b,c(from shaft collar)

 

Fq max

a

N

mm

3600 5000 6300 8000 11000 11000 16925 22000
17.5 17.5 20 20 22.5 22.5 26 29
Fq max

b

N

mm

2891 4046 4950 6334 8594 8594 13225 16809
30 30 35 35 40 40 46 50
Fq max

c

N

mm

2416 3398 4077 5242 7051 7051 108500 13600
42.5 42.5 50 50 57.5 57.5 66 71
Force axiale, max.

 

±Fax max N 1500 2200 2750 3500 4800 4800 6000 4150

Permissible input and through drive torques

Taille 40 60 75 95 130 190 190 260
Couple

(at Vg max and Δp = 350 bar 1)

Tmax Rien 234 326 412 521 724 808 1075 1448
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.2)

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 468 648 824 1044 1448 1448 2226 2787
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits Φ55 Φ60
at Z shaft end

DIN 5480

TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 912 912 1460 2190 3140 3140 3140 5780
W35 W35 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits W50 W50 W50 W60
at S shaft end

ANSI B92.1a-1976 (SAE J744)

TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 314 602 602 1640 1640 1640 1640 1640
1 po 1 1/4 po 1 1/4 po 1 3/4in 1 3/4in 1 3/4in 1 3/4in 1 3/4in
at T shaft end

ANSI B92.1a-1976 (SAE J744)

TcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Rien 602 970 970 - - - 2670 4070
1 1/4 in 1 3/8 in 1 3/8 in - - - 2 in 2 1/4 in
Through drive torque, max.3) TD perm. Rien 314 521 660 822 1110 1110 1760 2065

1)Efficiency not considered

2) For drive shafts with no radial force

3) Observe max. input torque for shaft S!

Torque distribution

Determining the nominal value

Flux qv=(Vg ∙ n ∙ ηv) / 1000 L/min
Couple T=(Vg ∙ Δp) / 20 ∙ π ∙ ηhm Rien
Puissance P=(2π ∙ T ∙ n)/60000=(qv ∙ Δp)/600 ∙ ηt kW

Vg = Displacement per revolution in cm3

Δp = Differential pressure in bar

n = Speed in rpm

ηv = Volumetric efficiency

ηhm = Mechanical-hydraulic efficiency

ηt = Overall efficiency (nt= nv* nhm)

A11VLO