A4VTG Hydrostatic Transmission Piston Pump

The A4VTG variable piston pump is listed for hydraulic transmission duty. Its reversible swashplate flow and auxiliary oil functions must be matched to the motor loop, control arrangement and machine duty cycle.

  • Auxiliary boost and pilot supply
  • Reversible flow through neutral
  • Pressure cut-off and relief functions
  • Through-drive option

PRANCE HYDRAULIC · PRODUCT SERIES

A4VTG Hydrostatic Transmission Piston Pump

Axial piston; variable swashplate · Closed-circuit transmission; confirm configuration

The A4VTG variable piston pump is listed for hydraulic transmission duty. Its reversible swashplate flow and auxiliary oil functions must be matched to the motor loop, control arrangement and machine duty cycle.

Modèle

✓A4VTG original product photograph
A4VTGAxial piston; variable swashplate
Demander un devisVoir les données techniques et la fiche technique

Confirm the complete model and approved specification with Prance Hydraulic. Product-series references alone do not establish interchangeability.

Étude de configuration · Documentation technique · Sélection de produits

Détails du produit

  • Auxiliary boost and pilot supply
  • Reversible flow through neutral
  • Pressure cut-off and relief functions
  • Through-drive option

CATÉGORIES : Pompe à piston, Pompe à cylindrée variable

A4VTG Features & Application

Auxiliary boost and pilot supply

Account for pilot or replenishment demand and the relevant pressure limits. Include filtration and the return or drain route in the circuit review.

Reversible flow through neutral

Review combined drive torque and simultaneous demand, including any additional pump connected to the drive.

Pressure cut-off and relief functions

Keep continuous, intermittent and peak conditions separate. Use the row for the selected size and configuration.

Through-drive option

Review combined drive torque and simultaneous demand, including any additional pump connected to the drive.

A4VTG Specifications

Series / modelA4VTG
Product typeA4VTG Hydrostatic Transmission Piston Pump
ConceptionAxial piston; variable swashplate
Circuit / selectionClosed-circuit transmission; confirm configuration
Product roleHydrostatic transmission pump
Auxiliary circuitConfirm boost pressure, pilot supply and filtration requirements

A4VTG Selection & Configuration

The A4VTG variable piston pump is listed for hydraulic transmission duty. Its reversible swashplate flow and auxiliary oil functions must be matched to the motor loop, control arrangement and machine duty cycle.

Review transmission startup, neutral, reversal and stopping as operating states. Check charge supply, cooling and replenishment during each state, and confirm the exact control and drive interface rather than selecting from displacement alone.

A4VTG original product view

Your Application.
The Right Configuration.

Hydraulic pumps · Hydraulic motors · Hydraulic valves

Send the MS nameplate, operating requirements and installation drawing for a configuration review before quoting.

  • Model review — send the full model code or an existing nameplate photograph.
  • Interface matching — confirm shaft, mounting flange, rotation and ports.
  • Operating conditions — provide flow, pressure, speed, fluid and duty cycle.
  • Documentation — request the relevant product data and drawings for your review.
Prance workshop with a row of production equipment

A4VTG Buying Guide

Use this sequence to prepare the A4VTG configuration for review and quotation.

  1. Define required flow at the actual drive speed and continuous pressure.
  2. Identify peak pressure, duration and the work cycle.
  3. Confirm the selected displacement control and any auxiliary-drive requirement.
  4. Match rotation viewed from the shaft end, shaft, flange and ports.
  5. Review inlet conditions, drain routing and the installation envelope.
  6. Confirm fluid, viscosity, temperature, filtration and seals.
  7. Approve the complete model, control, drawing, quantity and delivery terms.
A4VTG original product photograph for installation review

Selection, Documentation & Project Support

Prance technical team image from its company website

Selection Support

Learn more →

Share your hydraulic circuit, operating point and installation requirements for a configuration discussion.


Flow · Pressure · Speed · Interfaces
Prance quality standards image from its company website

Technical Resources

Learn more →

Review product documentation, model codes and technical data before finalizing the specification.


Datasheets · Model codes · Drawings
Prance sales team image from its company website

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Learn more →

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.


cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Configuration, Quantity & Delivery

Confirm the complete MS code, approved drawing and operating limits. Availability, quantity, documentation and delivery date are confirmed in the quotation.

Discuss Your A4VTG Application

Send the full model code, operating duty, installation details and quantity.

Request a A4VTG Quotation

A4VTG Questions Before Ordering

What type of product is the A4VTG?

A4VTG Hydrostatic Transmission Piston Pump. Design: Axial piston; variable swashplate. Closed-circuit transmission; confirm configuration. Confirm the complete order code for the offered version.

Can a similar pump replace the A4VTG?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Define required flow at the actual drive speed and continuous pressure. Identify peak pressure, duration and the work cycle. Attach the nameplate, complete order code, installation drawing and required quantity.

A4VTG Technical Data & Documents

View A4VTG catalog data and operating conditions

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

Données techniques

Huile hydraulique

Before starting project planning, please refer to our data sheets RE 90220 (mineral oil) and RE 90221 (environmentally acceptable hydraulic fluids) for detailed information regarding the choice of hydraulic fluids and application conditions. The A4VTG variable pump is not suitable for operation with HFA, HFB and HFC. If HFD or environmentally acceptable hy-draulic fluids are being used, the limitations regarding technical data and seals must be observed.Please contact us. When ordering, indicate the hydraulic fluid that is to be used.

Diagramme de sélection

A4VSO technical reference from the existing product documentation

Details regarding the choice of hydraulic fluid

The correct choice of hydraulic fluid requires knowledge of the operating temperature in relation to the ambient temperature: in a closed circuit the circuit temperature. The hydraulic fluid should be chosen so that the operating viscosity in the operating temperature range is within the optimum range (vopt), see shaded area of the selection diagram. We recommended that the higher viscosity class be selected in each case. Example: At an ambient temperature of X °C, an operating temperature of 60 °C is set in the circuit. In the optimum operating viscosity range (vopt.shaded area), this corresponds to the viscosity classes VG 46 or VG 68; to be selected: VG 68.

Remarque

The case drain temperature, which is affected by pressure and speed, is always higher than the circuit temperature. At no point of the component may the temperature be higher than115 °C, however. The temperature difference specified below is to be taken into account when determining the viscosity in the bearing. If the above conditions cannot be maintained due to extreme operating parameters, please contact us.

Viscosity and temperature

Viscosity [mm2/s] Temperature Comment
Storage Tmin ≥ -50 °C up to 12 months with standard factory conservation
Topt = +5 °C to +20 °C up to 24 months with long-term factory conservation
(Cold) start-up1) Permissible tempera- ture difference Vmax=1600 TSt≥ -40°C t≤3 min, without load (p≤50 bar), n ≤ 1000 rpm
ΔT≤25K between axial piston unit and hydraulic fluid
Warm-up phase v<1600to400 T=-40 °C to-25°C at Pnom,cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsnom cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Operating phase Temperature difference cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits The temperature of the hydraulic fluid in the bearing is (depending on pressure and speed) approx. 5 K higher than that of the case drain fluid at port T.
Continuous operation v=400 to 10 Vopt=16 to 36 T=-25°C to +90 °C no restriction within the permissible data
Short-term operation Vmin=<10to5 Tmax = +115 °C t<3 min,p<0.3·Pnom
Shaft seal ring FKM1) T≤ +115°C see page 5
1)At temperatures below -25 °C, an NBR shaft seal ring is required (permissible temperature range: -40 °C to +90 °C)

Filtration of the hydraulic fluid

Filtration improves the cleanliness level of the hydraulic fluid,which, in turn, increases the service life of the axial piston unit. To ensure the functional reliability of the axial piston unit, a gravimetric evaluation is necessary for the hydraulic fluid to determine the amount of contamination by solid matter and to determine the cleanliness level according to ISO 4406. A cleanliness level of at least 20/18/15 is to be maintained. Depending on the system and the application, for the A4VTG,we recommend Filter cartridges β20 > 100. With an increasing differential pressure at the filter cartridges,the B-value must not deteriorate. At very high hydraulic fluid temperatures (90 °C to maximum 115 °C), a cleanliness level of at least 19/17/14 according to ISO 4406 is necessary. If the above classes cannot be achieved, please contact us. For notes on filtration types, see page 16.

Shaft seal ring

Permissible pressure loading The service life of the shaft seal ring is affected by the speed of the pump and the case drain pressure. It is recommended that the average, continuous case drain pressure 3 bar absolute at operating temperature not be exceeded (maximum permissible case drain pressure 6 bar absolute at reduced speed,see diagram). Short-term (t <0.1 s) pressure spikes of up to10 bar absolute are permitted. The service life of the shaft seal ring decreases with an increase in the frequency of pressure spikes. The case pressure must be equal to or greater than the external pressure on the shaft seal ring. A4VSO technical reference from the existing product documentation

Temperature range

The FKM shaft seal ring may be used for case drain temperatures from-25 °C to +115 °C.

 Remarque

For application cases below -25 °C, an NBR shaft seal ring is necessary (permissible temperature range: -40 °C to +90 °C). State NBR shaft seal ring in plain text when ordering. Please contact us.

Operating pressure range

Pressure at service line port A or B Nominal pressure pnom———– 400 bar absolute Maximum pressure Pmax———– 450 bar absolute Single operating period————– 10s Total operating period————– 300h Minimum pressure (high-pressure side)———— 25 bar Minimum pressure (inlet)————–10 bar(boost pressure setting must be higher depending on system) Rate of pressure change RcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits———— 9000 bar/s A4VSO technical reference from the existing product documentation

Boost pump

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitscURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitss maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsSp cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsSp nomcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsSp maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsSt min cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Definition

Pression nominale Pnom cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsmax cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsA Maximum permissible rate of pressure build-up and pressure reduction during a pressure change over the entire pressure range. A4VSO technical reference from the existing product documentation

Table of values (theoretical values, without efficiency levels and tolerances; values rounded)

Taille NG 71 90
Déplacement variable pump Vg max cm3 70 90
boost pump (at p = 20 bar) Vg Sp cm3 20.5 27
Vitesse à VGiga nnom tours par minute 3300 3050
minimum nmin tours par minute 500 500
Couple1) à VGiga et Δp = 400 bar Tmax Rien 452 573
Δp = 100 bar T Rien 113 143
Rigidité rotative drive shaft V8 c Nm/rad 120900 –
drive shaft V9 c Nm/rad – 150896
Moment d'inertie pour le groupe rotatif JGR Kgm2 0.0097 0.0149
Accélération angulaire maximale2) α rad/s2 21000 18000
Filling capacity V L 1.3 1.2
Mass approx. (without through drive) m kg 51 53
1)Without boost pump 2) The area of validity lies between the minimum required and maximum permissible speed. It applies for external stimuli (e. g. engine 2 to 8 times rotary frequency, cardan shaft twice the rotary frequency). The limit value applies for a single pump only. The load capacity of the connection parts must be considered.

Remarque

Operation above the maximum values or below the minimum values may result in a loss of function, a reduced service life or in the destruction of the axial piston unit. We recommend testing the loads by means of experiment or calculation/simulation and comparison with the permissible values.

Définir les caractéristiques de fonctionnement

Vg = Displacement per revolution in cm3 Δp = Differential pressure in bar n = Speed in rpm ηv = Volumetric efficiency ηhm = Mechanical-hydraulic efficiency ηt cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitst= ηvcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitshm)

Charge radiale et axiale admissible sur l'arbre d'entraînement

Taille NG 71 90
Arbre de transmission in 1 3/8 1 1/2
Radial force maximum at distance a (from shaft collar) A4VSO technical reference from the existing product documentation Fq max a N mm 5600 24 7100 24
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits A4VSO technical reference from the existing product documentation +Fax max N 4242 4330
-Fax max N 2758 2670

Remarque

Special requirements apply in the case of belt drives. Please contact us. Force-transfer direction of the permissible axial force: + Fhache max=Increase in service life of bearings – Fhache maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

couples d'entrée et de transmission admissibles

Taille NG 71 90
Input torque at drive shaft, maximum2) V8 Rien TEmax Rien 970 –
V9 Rien TEmax Rien – 1305
Couple maximal en traversée TDmax Rien 250 250
1)Efficiency not considered 2) For drive shafts with no radial force

Request a A4VTG Quotation

Tell us your required configuration, quantity and application.

Démo du formulaire de contact
A4VTG original product photograph

Ordering code for standard program

A4VT G / 33 M N C4 F A S
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18

Unité à pistons axiaux

01 Swashplate design, variable, nominal pressure 400 bar, maximum pressure 450 bar, mobile concrete mixers A4VT

Mode de fonctionnement

02 Pompe, circuit fermé G

Taille

03 Displacement Vg monx en cm3 071 090

Dispositif de commande

071 090
04 Proportional control hydraulic, mechanical servo, hexagon shaft with lever to the rear ● ● HW11)
Proportional control electric,

with emergency actuation and spring return

U=12VDC ● ● ÉP3
U=24 VDC ● ● EP4

Connecteur pour solénoïdes2)

071 090
05 Sans ● ● 0
Connecteur moulé DEUTSCH, 2 broches - sans diode de suppression ● ● P

Auxiliary functions

071 090
06 Sans ● ● 0
With mechanical stroke limiter, externally adjustable ● ● M
With ports X3, X4 for stroking chamber pressure ● ● T
With mechanical stroke limiter and ports X3, X4 ● ● B

Séries

07 Series 3, Index 3 33

Version of port and fixing threads

08 Metric M

Sens de rotation

09 Viewed from drive shaft dans le sens des aiguilles d'une montre R
anti-clockwise L

Joints d'étanchéité

10 NBR (caoutchouc nitrile), anneau d'étanchéité d'arbre en FKM (caoutchouc fluoré) N

Bride de fixation

11 SAEJ744, 127-4 C4

Arbre de transmission

071 090
12 Arbre cannelé

ANSIB92.1a-1976

1 3/8 in 21T 16/32DP without coupling flange ● - V8
with coupling flange ● - C8
1 1/2 in 23T 16/32DP without coupling flange - ● V9
with coupling flange - ● C9

Ports de ligne de service

071 090
13 SAE flange port

A and B on same side

left Suction port S at bottom ○ ○ 1
right Suction port S at top ● ● 2

• = disponible ○ = sur demande - = non disponible

1)Mounting position of the lever not specified on delivery, to be aligned by the customer

2) Connectors for other electric components can deviate.

Boost pump

14 With integrated boost pump F

Drive

15 Bride SAE J744 Coupling for splined shaft1)
Mounting variant
Diamètre Symbol Designation Diamètre Designation 071 090
Sans ● ● 0000
82-2 A2 cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits S2 ● ● cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
101-2 B2 7/8 in 13T cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits S4 ● ● B2S4

High-pressure valves

16 With high-pressure relief valve, direct controlled A

Filtration boost circuit

17 Filtration in the boost pump suction line S

Version standard / spéciale

12 Version standard -0
combined with attachment part or attachment pump -K
Version spéciale -S
combined with attachment part or attachment pump -T

Remarque

Short designation X refers to a special version not covered by the ordering code.

• = disponible ○ = sur demande - = non disponible

3) Coupling for splined shaft acc. ANSI B92.1a-1976

Données techniques

Huile hydraulique

Before starting project planning, please refer to our data sheets RE 90220 (mineral oil) and RE 90221 (environmentally acceptable hydraulic fluids) for detailed information regarding the choice of hydraulic fluids and application conditions.

The A4VTG variable pump is not suitable for operation with HFA, HFB and HFC. If HFD or environmentally acceptable hy-draulic fluids are being used, the limitations regarding technical data and seals must be observed.Please contact us.

When ordering, indicate the hydraulic fluid that is to be used.

Diagramme de sélection

Details regarding the choice of hydraulic fluid

The correct choice of hydraulic fluid requires knowledge of the operating temperature in relation to the ambient temperature: in a closed circuit the circuit temperature.

The hydraulic fluid should be chosen so that the operating viscosity in the operating temperature range is within the optimum range (vopt), see shaded area of the selection diagram. We recommended that the higher viscosity class be selected in each case.

Example: At an ambient temperature of X °C, an operating temperature of 60 °C is set in the circuit. In the optimum operating viscosity range (vopt.shaded area), this corresponds to the viscosity classes VG 46 or VG 68; to be selected: VG 68.

Remarque

The case drain temperature, which is affected by pressure and speed, is always higher than the circuit temperature. At no point of the component may the temperature be higher than115 °C, however. The temperature difference specified below is to be taken into account when determining the viscosity in the bearing.

If the above conditions cannot be maintained due to extreme operating parameters, please contact us.

Viscosity and temperature

Viscosity [mm2/s] Temperature Comment
Storage Tmin ≥ -50 °C up to 12 months with standard factory conservation
Topt = +5 °C to +20 °C up to 24 months with long-term factory conservation
(Cold) start-up1)

Permissible tempera-

ture difference

Vmax=1600 TSt≥ -40°C t≤3 min, without load (p≤50 bar), n ≤ 1000 rpm
ΔT≤25K between axial piston unit and hydraulic fluid
Warm-up phase v<1600to400 T=-40 °C to-25°C at Pnom,cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsnom cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Temperature

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits The temperature of the hydraulic fluid in the bearing is (depending on pressure and speed) approx. 5 K higher than that of the case drain fluid at port T.
Continuous operation v=400 to 10

Vopt=16 to 36

T=-25°C to +90 °C no restriction within the permissible data
Short-term operation Vmin=<10to5 Tmax = +115 °C t<3 min,p<0.3·Pnom
Shaft seal ring FKM1) T≤ +115°C see page 5

1)At temperatures below -25 °C, an NBR shaft seal ring is required

(permissible temperature range: -40 °C to +90 °C)

Filtration of the hydraulic fluid

Filtration improves the cleanliness level of the hydraulic fluid,which, in turn, increases the service life of the axial piston unit.

To ensure the functional reliability of the axial piston unit, a gravimetric evaluation is necessary for the hydraulic fluid to determine the amount of contamination by solid matter and to determine the cleanliness level according to ISO 4406. A cleanliness level of at least 20/18/15 is to be maintained.

Depending on the system and the application, for the A4VTG,we recommend

Filter cartridges β20 > 100.

With an increasing differential pressure at the filter cartridges,the B-value must not deteriorate.

At very high hydraulic fluid temperatures (90 °C to maximum 115 °C), a cleanliness level of at least 19/17/14 according to ISO 4406 is necessary.

If the above classes cannot be achieved, please contact us.

For notes on filtration types, see page 16.

Shaft seal ring

Permissible pressure loading

The service life of the shaft seal ring is affected by the speed of the pump and the case drain pressure. It is recommended that the average, continuous case drain pressure 3 bar absolute at operating temperature not be exceeded (maximum permissible case drain pressure 6 bar absolute at reduced speed,see diagram). Short-term (t <0.1 s) pressure spikes of up to10 bar absolute are permitted. The service life of the shaft seal ring decreases with an increase in the frequency of pressure spikes.

The case pressure must be equal to or greater than the external pressure on the shaft seal ring.

Temperature range

The FKM shaft seal ring may be used for case drain temperatures from-25 °C to +115 °C.

 Remarque

For application cases below -25 °C, an NBR shaft seal ring is necessary (permissible temperature range: -40 °C to +90 °C).

State NBR shaft seal ring in plain text when ordering.

Please contact us.

Operating pressure range

Pressure at service line port A or B

Nominal pressure pnom----------- 400 bar absolute

Maximum pressure Pmax----------- 450 bar absolute

Single operating period-------------- 10s

Total operating period-------------- 300h

Minimum pressure (high-pressure side)------------ 25 bar

Minimum pressure (inlet)--------------10 bar(boost pressure setting must be higher depending on system)

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitscURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitscURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Boost pump

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitscURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits2cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Maximum ps max----------------≤5 bar absolute

Standard adjustment pSp (at n= 1500 rpm)------------ 22 bar

Nominal pressure pSp nom--------------- 30 bar

Maximum pressure pSp max--------------- 0 bar

Control pressure

To ensure the function of the control, the following control pressure is required depending on the speed and operating pressure (measurement point, port Ps):

For controls EP and HW

Minimum control pressure PSt min (at n = 1500 rpm)--- 22 bar

Definition

Pression nominale Pnom

The nominal pressure corresponds to the maximum design pressure.

Maximum pressure pmax

The maximum pressure corresponds the maximum operating pressure within the single operating period. The sum of the single operating period must not exceed the total operating period.

Minimum pressure (high-pressure side)

Minimum pressure on the high-pressure side (A or B) that is required in order to prevent damage to the axial piston unit.

Minimum pressure (inlet)

Minimum pressure in inlet (A or B) that is required in order to prevent damage to the axial piston unit.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsA

Maximum permissible rate of pressure build-up and pressure reduction during a pressure change over the entire pressure range.

Table of values (theoretical values, without efficiency levels and tolerances; values rounded)

Taille NG 71 90
Déplacement variable pump Vg max cm3 70 90
boost pump (at p = 20 bar) Vg Sp cm3 20.5 27
Vitesse à VGiga nnom tours par minute 3300 3050
minimum nmin tours par minute 500 500
Flux à nnom H et Vg max qv max L/min 234 275
Puissance1) à nnom H, VGiga Δp = 400 bar Pmax kW 156 183
Couple1) à VGiga et Δp = 400 bar Tmax Rien 452 573
Δp = 100 bar T Rien 113 143
Rigidité rotative drive shaft V8 c Nm/rad 120900 -
drive shaft V9 c Nm/rad - 150896
Moment d'inertie pour le groupe rotatif JGR Kgm2 0.0097 0.0149
Accélération angulaire maximale2) α rad/s2 21000 18000
Filling capacity V L 1.3 1.2
Mass approx. (without through drive) m kg 51 53

1)Without boost pump

2) The area of validity lies between the minimum required and maximum permissible speed.

It applies for external stimuli (e. g. engine 2 to 8 times rotary frequency, cardan shaft twice the rotary frequency).

The limit value applies for a single pump only.

The load capacity of the connection parts must be considered.

Remarque

Operation above the maximum values or below the minimum values may result in a loss of function, a reduced service life or in the destruction of the axial piston unit. We recommend testing the loads by means of experiment or calculation/simulation and comparison with the permissible values.

Définir les caractéristiques de fonctionnement

Flux qv=(Vg ∙ n ∙ ηv) / 1000 L/min
Couple T=(Vg ∙ Δp) /(20 ∙ π ∙ ηhm) Rien
Puissance P=(2π ∙ T ∙ n)/60000=(qv ∙ Δp)/(600 ∙ ηt)  kW

Vg = Displacement per revolution in cm3

Δp = Differential pressure in bar

n = Speed in rpm

ηv = Volumetric efficiency

ηhm = Mechanical-hydraulic efficiency

ηt cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitst= ηvcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitshm)

Charge radiale et axiale admissible sur l'arbre d'entraînement

Taille NG 71 90
Arbre de transmission in 1 3/8 1 1/2
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

Fq max

a

N

mm

5600

24

7100

24

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits +Fax max N 4242 4330
-Fax max N 2758 2670

Remarque

▶Des exigences particulières s'appliquent en cas de transmissions par courroie. Veuillez nous contacter.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

+ Fhache maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

- Fhache maxcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

couples d'entrée et de transmission admissibles

Taille NG 71 90
Couple à VGiga and Δp= 400 bar)1) Tmax Rien 452 573
Couple d'entrée

at drive shaft, maximum2)

V8 Rien TEmax Rien 970 -
V9 Rien TEmax Rien - 1305
Couple maximal en traversée TDmax Rien 250 250

1)Efficiency not considered

2) For drive shafts with no radial force